- 您現在的位置：買賣IC網 > PDF目錄69022 > MB91F353APMT RISC MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB91F353APMT |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | RISC MICROCONTROLLER, PQFP120 |
| 封裝： | 16 X 16 MM, 1.70 MM HEIGHT, 0.50 MM PPITCH, LEAD FREE, PLASTIC, LQFP-120 |
| 文件頁數： | 57/140頁 |
| 文件大?。?/td> | 3803K |
| 代理商： | MB91F353APMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁
MB91350A Series
DS07-16503-5E
23
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage greater than VCC or less than VSS is applied to an input or output
pin or if an above-rating voltage is applied between VCC and VSS. A latch-up,if it occurs, significantly increases
the power supply current and may cause thermal destruction of an element. When you use a CMOS IC, don’t
exceed the absolute maximum rating.
Treatment of Unused Pins
Do not leave unused input pins open, as this may cause a malfunction. Handle by using a pull-up or pull-down
resistor.
Power Supply Pins
In products with multiple VCC and VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to the external power
supply and ground lines in order to lower the electro-magnetic emission level, to prevent abnormal operation of
strobe signals caused by the rise in the ground level, and to conform to the total output current rating. Moreover,
connect the current supply source to the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS pins
near this device.
Crystal Oscillator Circuit
Noise near the X0, X1, X0A and X1A pins may cause the device to malfunction. Design the printed circuit board
so that X0, X1, X0A, X1A, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are
located close to the device as possible.
It is strongly recommended that the PC board artwork be designed such that the X0, X1, X0A and X1A pins are
surrounded by ground plane, as stable operation can be obtained by using this layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
Notes on Using an External Clock
When using an external clock, as a general rule you should simultaneously supply the clock signal to X0 and a
clock signal with the reverse phase to X1. However, the stop mode (oscillator stop mode) must not be used
under this configuration (This is because the X1 pin stops at High level output in STOP mode) .
Using an external clock (normal)
Clock Control Block
Hold the signal for the oscillation stabilization wait time when inputting a Low level to the INIT pin.
X0
X1
Note : STOP mode (oscillation stop mode) cannot be used.
MB91350A series
相關PDF資料 |
PDF描述 |
|---|---|
| MB91354APMT | 32-BIT, MROM, 50 MHz, RISC MICROCONTROLLER, PQFP176 |
| MB91F356BPMT | RISC MICROCONTROLLER, PQFP176 |
| MB91461PMC-GSE1 | RISC MICROCONTROLLER, PQFP176 |
| MB91664PMC | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP120 |
| MB91661PMC | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP120 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F353APMT-GE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU 5V SMD LQFP120 |
| MB91F354A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit Proprietary Microcontroller |
| MB91F355A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F355APMCR-G-002E1 | 制造商:FUJITSU 功能描述: |
| MB91F355APMT-002 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。