參數資料
型號： MBM29F002BC-90
廠商： Fujitsu Limited
英文描述： 2M (256K X 8) BIT
中文描述： 200萬（256K × 8）位
文件頁數： 12/46頁
文件大?。?/td> 461K
代理商： MBM29F002BC-90
12
MBM29F002TC
-55/-70/-90
/MBM29F002BC
-55/-70/-90
Temporary Sector Unprotection
This feature allows temporary unprotection of previously protected sectors of the MBM29F002TC/BC device in
order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage (12
V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses.
Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected again.
Refer to Figures 14 and 21.
Notes:
1.Address bits A
11
to A
17
= X = “H” or “L” for all address commands except or Program Address (PA) and
Sector Address (SA).
2.Bus operations are defined in Table 2.
3.RA = Address of the memory location to be read.
PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of
the WE pulse.
SA = Address of the sector to be erased. The combination of A
17
, A
16
, A
15
, A
14
, and A
13
will uniquely select
any sector.
4.RD = Data read from location RA during read operation.
PD = Data to be programmed at location PA. Data is latched on the rising edge of WE.
ID = Device Code (Refer to the section on Sector Protection Verify Autoselect Codes.)
*: Either of the two reset commands will reset the device.
Command Definitions
Device operations are selected by writing specific address and data sequences into the command register.
Writing incorrect address and data values or writing them in the improper sequence will reset the device to the
read mode. Table 6 defines the valid register command sequences. Note that the Erase Suspend (B0H) and
Erase Resume (30H) commands are valid only while the Sector Erase operation is in progress. Moreover, both
Read/Reset commands are functionally equivalent, resetting the device to the read mode.
Table 6 MBM29F002TC/BC Command Definitions
Command
Sequence
Bus
Write
Cycles
Req'd
First Bus
Write Cycle
Second Bus
Write Cycle
Third Bus
Write Cycle
Fourth Bus
Read/Write
Cycle
Fifth Bus
Write Cycle
Sixth Bus
Write Cycle
Addr. Data Addr. Data Addr. Data Addr. Data Addr. Data Addr. Data
Read/Reset*
1
XXXH F0H
—
—
—
—
—
—
—
—
—
—
Reset/Read*
3
555H AAH
2AAH
55H
555H
F0H
RA
RD
—
—
—
—
Manufacture Code
3
555H AAH
2AAH
55H
555H
90H
00H
04H
—
—
—
—
Device Code
3
555H AAH
2AAH
55H
555H
90H
01H
ID
—
—
—
—
Byte Program
4
555H AAH
2AAH
55H
555H
A0H
PA
PD
—
—
—
—
Chip Erase
6
555H AAH
2AAH
55H
555H
80H
555H
AAH
2AAH
55H
555H
10H
Sector Erase
6
555H AAH
2AAH
55H
555H
80H
555H
AAH
2AAH
55H
SA
30H
Sector Erase Suspend
Erase can be suspended during sector erase with Addr (“H” or “L”), Data (B0H)
Sector Erase Resume
Erase can be resumed after suspend with Addr (“H” or “L”), Data (30H)
相關PDF資料
PDF描述
MBM29F002TC-55 2M (256K X 8) BIT
MBM29F002TC 2M (256K X 8) BIT
MBM29F002TC-90 2M (256K X 8) BIT
MBM29F002B 2M (256K ×8) Bit Flash Memory( 單5V 電源電壓256K ×8位閃速存儲器)
MBM29F002SB 2M (256K ×8) Bit Flash Memory( 單5V 電源電壓256K ×8位閃速存儲器)
相關代理商/技術參數
參數描述
MBM29F002T-90PD# 制造商:FUJITSU 功能描述:
MBM29F002TC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8) BIT
MBM29F002TC-55 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8) BIT
MBM29F002TC-70 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8) BIT
MBM29F002TC-90 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*