- 您現在的位置：買賣IC網 > PDF目錄359133 > MC33991 (飛思卡爾半導體(中國)有限公司) Gauge Driver Integrated Circuit(標尺驅動器集成電路) PDF資料下載
參數資料
| 型號： | MC33991 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Gauge Driver Integrated Circuit(標尺驅動器集成電路) |
| 中文描述： | 儀表驅動集成電路（標尺驅動器集成電路） |
| 文件頁數： | 15/36頁 |
| 文件大小： | 660K |
| 代理商： | MC33991 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33991
15
These bits are
write-only
.
PE12–Null Command for Status Read
0 = Disable
1 = Enable
PE11–PE5—These bits must be transmitted as logic [0] for
valid PECR commands.
PE4–Clock Calibration Frequency Selector
0 = Maximum f = 1 MHz (for 8 μs calibration pulse)
1 = Nominal f = 1 MHz (for 8 μs calibration pulse)
PE3–Clock Calibration Enable—This bit enables or disables
the clock calibration.
0 = Disable
1 = Enable
PE2–Oscillator Adjustment
0 = Tosc
1 = 0.66 x Tosc
PE1–Gauge 1 Enable—This bit enables or disables the
output driver of Gauge 1.
0 = Disable
1= Enable
PE0–Gauge 0 Enable—This bit enables or disables the
output driver of Gauge 0.
0 = Disable
1 = Enable
Maximum Velocity Register (VELR)
SIAddress001—GaugeMaximumVelocityRegister,isused
to set a maximum velocity for each gauge. See Table 4.
Bits D7-D0 contain a position value from 1-255
representative of the table position value. The table value
becomes the maximum velocity until it is changed to another
value. If a maximum value is chosen greater than the maximum
velocity in the acceleration table, the maximum table value will
become the maximum velocity. If the motor is turning at a value
greater than the new maximum, the motor will ignore the new
value until the speed falls equal to, or below it. Velocity for each
motor can be changed simultaneously, or independently, by
writing D8 and/or D9 to a logic [1]. Bits D10 –D12 must be at
logic [0] for valid VELR commands.
These bits are
write-only
.
V12–V10—These bits must be transmitted as logic [0] for
valid VELR commands.
V9–Gauge 1 Velocity—Specifies whether the maximum
velocity determined in the V7-V0 field applies to Gauge 1
0 = Velocity does not apply to Gauge 1
1 = Velocity applies to Gauge 1
V8–Gauge 0 Velocity—Specifies whether the maximum
velocity specified in the V7-V0 field applies to Gauge 0
0 = Velocity does not apply to Gauge 0
1 = Velocity applies to Gauge 0
V7–V0 Maximum Velocity—Specifies the maximum velocity
positionfromthe accelerationtable. Thisvelocitywill remainthe
maximum of the intended gauge until changed by command.
Velocities can range from position 1 (00000001) to position 255
(11111111).
Gauge 0/1 Position Register (POS0R, POS1R)
SI Addresses 010—Gauge 0 Position Register receives
writing when communicating the desired pointer positions.
SI Address 011—Gauge 1 Position Register receives writing
when communicating the desired pointer positions.
Register bits D11–D0 receives writing when communicating
the desired pointer positions.
Commandedpositionscanrangefrom0to4095.TheD12bit
must be at logic [0] for valid POS0R and POS1R commands.
Table 3. Power, Enable and Calibration Register (PECR)
Address 000
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Write
PE12
0
0
0
0
0
0
0
PE4
PE3
PE2
PE1
PE0
Table 4. Maximum Velocity Register (VELR)
Address 001
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Write
0
0
0
V9
V8
V7
V6
V5
V4
V3
V2
V1
V0
F
Freescale Semiconductor, Inc.
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33993 | Multiple Switch Detection Interface(多開關監測接口) |
| MC33997 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
| MC33998 | Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源) |
| MC34017 | Telephone Tone Ringer(電話振鈴) |
| MC34063A | DC-DC CONVERTER CONTROL CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33991DW | 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit |
| MC33991DWR2 | 制造商:Rochester Electronics LLC 功能描述:GUAGE DRIVER IC - Bulk |
| MC33993DWB | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33993DWBR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MC33996EK | 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。