參數資料
型號: MC68332MFV16
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 32-Bit Modular Microcontroller
中文描述: 32-BIT, 16.78 MHz, MICROCONTROLLER, PQFP144
封裝: QFP-144
文件頁數: 25/88頁
文件大小: 446K
代理商: MC68332MFV16
MC68332
MC68332TS/D
MOTOROLA
25
3.3.3 Clock Control
The clock control circuits determine system clock frequency and clock operation under special circum-
stances, such as following loss of synthesizer reference or during low-power operation. Clock source is
determined by the logic state of the MODCLK pin during reset.
When the on-chip clock synthesizer is used, system clock frequency is controlled by the bits in the upper
byte of SYNCR. Bits in the lower byte show status of or control operation of internal and external clocks.
The SYNCR can be read or written only when the CPU is operating at the supervisor privilege level.
W — Frequency Control (VCO)
This bit controls a prescaler tap in the synthesizer feedback loop. Setting the bit increases the VCO
speed by a factor of four. VCO relock delay is required.
X — Frequency Control Bit (Prescale)
This bit controls a divide by two prescaler that is not in the synthesizer feedback loop. Setting the bit
doubles clock speed without changing the VCO speed. There is no VCO relock delay.
Y[5:0] — Frequency Control (Counter)
The Y field controls the modulus down counter in the synthesizer feedback loop, causing it to divide by
a value of Y
+
1. Values range from 0 to 63. VCO relock delay is required.
EDIV — E Clock Divide Rate
0 = ECLK frequency is system clock divided by 8.
1 = ECLK frequency is system clock divided by 16.
ECLK is an external M6800 bus clock available on pin ADDR23. Refer to
3.5 Chip Selects
for more
information.
SLIMP — Limp Mode Flag
0 = External crystal is VCO reference.
1 = Loss of crystal reference.
When the on-chip synthesizer is used, loss of reference frequency causes SLIMP to be set. The VCO
continues to run using the base control voltage. Maximum limp frequency is maximum specified system
clock frequency. X-bit state affects limp frequency.
SLOCK — Synthesizer Lock Flag
0 = VCO is enabled, but has not locked.
1 = VCO has locked on the desired frequency (or system clock is external).
The MCU maintains reset state until the synthesizer locks, but SLOCK does not indicate synthesizer
lock status until after the user writes to SYNCR.
RSTEN — Reset Enable
0 = Loss of crystal causes the MCU to operate in limp mode.
1 = Loss of crystal causes system reset.
STSIM — Stop Mode SIM Clock
0 = When LPSTOP is executed, the SIM clock is driven from the crystal oscillator and the VCO is
turned off to conserve power.
1 = When LPSTOP is executed, the SIM clock is driven from the VCO.
STEXT — Stop Mode External Clock
0 = When LPSTOP is executed, the CLKOUT signal is held negated to conserve power.
1 = When LPSTOP is executed, the CLKOUT signal is driven from the SIM clock, as determined by
the state of the STSIM bit.
SYNCR
—Clock Synthesizer Control Register
$YFFA04
15
14
13
8
7
6
5
4
3
2
1
0
W
X
Y
EDIV
0
0
SLIMP
SLOCK RSTEN
STSIM
STEXT
RESET:
0
0
1
1
1
1
1
1
0
0
0
U
U
0
0
0
相關PDF資料
PDF描述
MC68332 32-Bit Modular Microcontroller
MC68332ACFC16 32-Bit Modular Microcontroller
MC68332ACFC20 32-Bit Modular Microcontroller
MC68332ACFV16 32-Bit Modular Microcontroller
MC68332ACFV20 32-Bit Modular Microcontroller
相關代理商/技術參數
參數描述
MC68332MFV20 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller
MC68332TS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller
MC68332VFC16 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller
MC68332VFC20 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller
MC68332VFV16 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller