參數資料
型號： MC68HC11A1CFN3
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC52
封裝： PLASTIC, LCC-52
文件頁數： 125/158頁
文件大?。?/td> 3803K
代理商： MC68HC11A1CFN3
ANALOG-TO-DIGITAL CONVERTER
MOTOROLA
TECHNICAL DATA
7-5
7
7.7 A/D Result Registers 1, 2, 3, and 4 (ADR1, ADR2, ADR3, and ADR4)
The A/D result registers are read-only registers used to hold an 8-bit conversion result.
Writes to these registers have no effect. Data in the A/D result registers is valid when
the CCF flag bit in the ADCTL register is set, indicating a conversion sequence is com-
plete. If conversion results are needed sooner refer to Figure 7-1. For example the
ADR1 result is valid 33 cycles after an ADCTL write. Refer to the A/D channel assign-
ments in Table 7-1 for the relationship between the channels and the result registers.
7.8 A/D Power-Up and Clock Select
A/D power-up is controlled by bit 7 (ADPU) of the OPTION register. When ADPU is
cleared, power to the A/D system is disabled. When ADPU is set, the A/D system is
enabled. A delay of as much as 100 microseconds is required after turning on the A/
D converter to allow the analog bias voltages to stabilize.
Clock select is controlled by bit 6 (CSEL) of the OPTION register. When CSEL is
cleared, the A/D system uses the system E clock. When CSEL is set, the A/D system
uses an internal R-C clock source, which runs at about 1.5 MHz. The MCU E clock is
not suitable to drive the A/D system if it is operating below 750 kHz, in which case the
R-C internal clock should be selected. A delay of 10 ms is required after changing
CSEL from zero to one to allow the R-C oscillator to start and internal bias voltages to
settle. Refer to 9.1.5 Configuration Options Register (OPTION) for additional infor-
mation. Note that the CSEL control bit also enables a separate R-C oscillator to drive
the EEPROM charge pump.
When the A/D system is operating with the MCU E clock, all switching and comparator
operations are synchronized to the MCU clocks. This allows the comparator results to
be sampled at quiet clock times to minimize noise errors. The internal R-C oscillator is
asynchronous to the MCU clock so noise will affect A/D results more while CSEL = 1.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HCP11A1CP2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48
MC68HC11A1MFN2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC52
MC68HC11A1MFU2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64
MC68HC11A8BMP2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48
MC68HCP11A1VP2 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP48
相關代理商/技術參數
參數描述
MC68HC11A1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1CFNE3 制造商:Freescale Semiconductor 功能描述:8-BIT MICROCONTROLLER IC
MC68HC11A1CFNE3R 功能描述:8位微控制器 -MCU 8B MCU 256RAM A/D EE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC11A1CFU2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
MC68HC11A1CFU3 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS Single-Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*