參數資料
型號: MC68HC11D3CFN2
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 81/138頁
文件大?。?/td> 1047K
代理商: MC68HC11D3CFN2
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
47
Chapter 4
Resets, Interrupts, and Low-Power Modes
4.1 Introduction
This section describes the internal and external resets and interrupts of the MC68HC711D3 and its two
low power-consumption modes.
4.2 Resets
The microcontroller unit (MCU) can be reset in any of these four ways:
1.
An active-low input to the RESET pin
2.
A power-on reset (POR) function
3.
A clock monitor failure
4.
A computer operating properly (COP) watchdog timer timeout
The RESET input consists mainly of a Schmitt trigger that senses the RESET line logic level.
4.2.1 RESET Pin
To request an external reset, the RESET pin must be held low for at least eight E-clock cycles, or for one
E-clock cycle if no distinction is needed between internal and external resets.
4.2.2 Power-On Reset (POR)
Power-on reset occurs when a positive transition is detected on VDD. This reset is used strictly for power
turn on conditions and should not be used to detect any drop in the power supply voltage. If the external
RESET pin is low at the end of the power-on delay time, the processor remains in the reset condition until
RESET goes high.
4.2.3 Computer Operating Properly (COP) Reset
The MCU contains a watchdog timer that automatically times out unless it is serviced within a specific
time by a program reset sequence. If the COP watchdog timer is allowed to timeout, a reset is generated,
which drives the RESET pin low to reset the MCU and the external system.
In the MC68HC711D3, the COP reset function is enabled out of reset in normal modes. If the user does
not want the COP enabled, he must write a 1 to the NOCOP bit of the configuration control register
(CONFIG) after reset. This bit is writable only once after reset in normal modes (see 2.3.3 Configuration
Control Register for more information). Protected control bits (CR1 and CR0) in the configuration options
register (OPTION) allow the user to select one of the four COP timeout rates. Table 4-1 shows the
relationship between CR1 and CR0 and the COP timeout period for various system clock frequencies.
相關PDF資料
PDF描述
MC68HC11D3CFN3 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQCC44
MC68HC08JB1DW 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDSO20
MC68HC08JB1P 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDIP20
MC68HC912BL16FU8 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
MC68HC912BL16VFU8 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
MC68HC11D3CFN3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFN4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFU1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11D3CFU3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers