參數資料
型號： MC68HC11F1CFN3R2
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 145/174頁
文件大?。?/td> 981K
代理商： MC68HC11F1CFN3R2
MOTOROLA
RESETS AND INTERRUPTS
MC68HC11F1
5-10
TECHNICAL DATA
at the address specified by the vector. At the end of the interrupt service routine, the
return from interrupt instruction is executed and the saved registers are pulled from the
stack in reverse order so that normal program execution can resume. Refer to SEC-
TION 3 CENTRAL PROCESSING UNIT for further information.
5.4.2 Non-Maskable Interrupt Request (XIRQ)
Non-maskable interrupts are useful because they can always interrupt CPU opera-
tions. The most common use for such an interrupt is for serious system problems, such
as program runaway or power failure. The XIRQ input is an updated version of the NMI
input of earlier MCUs.
Upon reset, both the X bit and I bit of the CCR are set to inhibit all maskable interrupts
and XIRQ. After minimum system initialization, software can clear the X bit by a TAP
instruction, enabling XIRQ interrupts. Thereafter, software cannot set the X bit. Thus,
an XIRQ interrupt is a nonmaskable interrupt. Because the operation of the I-bit-relat-
ed interrupt structure has no effect on the X bit, the internal XIRQ pin remains non-
masked. In the interrupt priority logic, the XIRQ interrupt has a higher priority than any
source that is maskable by the I bit. All I-bit-related interrupts operate normally with
their own priority relationship.
When an I-bit-related interrupt occurs, the I bit is automatically set by hardware after
stacking the CCR byte. The X bit is not affected. When an X-bit-related interrupt oc-
curs, both the X and I bits are automatically set by hardware after stacking the CCR.
A return from interrupt instruction restores the X and I bits to their pre-interrupt request
state.
5.4.3 Illegal Opcode Trap
Because not all possible opcodes or opcode sequences are defined, the MCU in-
cludes an illegal opcode detection circuit, which generates an interrupt request. When
an illegal opcode is detected and the interrupt is recognized, the current value of the
program counter is stacked. After interrupt service is complete, reinitialize the stack
pointer so repeated execution of illegal opcodes does not cause stack underflow. Left
uninitialized, the illegal opcode vector can point to a memory location that contains an
illegal opcode. This condition causes an infinite loop that causes stack underflow. The
stack grows until the system crashes.
Table 5-5 Stacking Order on Entry to Interrupts
Memory Location
CPU Registers
SP
PCL
SP – 1
PCH
SP – 2
IYL
SP – 3
IYH
SP – 4
IXL
SP – 5
IXH
SP – 6
ACCA
SP – 7
ACCB
SP – 8
CCR
相關PDF資料
PDF描述
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68SZ328VH66V 66 MHz, RISC PROCESSOR, PBGA196
MC74F2970N DRAM CONTROLLER, PDIP24
MC908GP32CFBR2 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP44
MC908GP32CFBR2 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68HC11F1CFN4 功能描述:IC MCU 512 EEPROM 4MHZ 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC11F1CFN4R2 功能描述:IC MCU 1K RAM 4MHZ 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC11F1CFN5 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1CFU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1CFU1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*