參數資料
型號： MC68HC11F1CFN4R2
廠商： Freescale Semiconductor
文件頁數： 70/158頁
文件大?。?/td> 0K
描述： IC MCU 1K RAM 4MHZ 68-PLCC
標準包裝： 1
系列： HC11
核心處理器： HC11
芯體尺寸： 8-位
速度： 4MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 30
程序存儲器類型： ROMless
EEPROM 大?。?/td> 512 x 8
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.75 V ~ 5.25 V
數據轉換器： A/D 8x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 68-LCC（J 形引線）
包裝： 剪切帶 (CT)
其它名稱： MC68HC11F1CFN4RCT
PIN DESCRIPTIONS
TECHNICAL DATA
2-5
2.5 Four Times E-Clock Frequency Output (4XOUT)
Although the circuit shown in Figure 2-6 will work for any M68HC11 MCU, the
MC68HC11F1 has an additional clock output that is four times the E-clock frequency.
This output (4XOUT) can be used to directly drive the EXTAL input of another
M68HC11 MCU. Refer to Figure 2-7. The 4XOUT output is enabled after reset and
can be disabled by clearing the CLK4X bit in the OPT2 register.
Figure 2-7 4XOUT Signal Driving a Second MCU
2.6 Interrupt Request (IRQ)
The IRQ input provides a means of generating asynchronous interrupt requests for the
CPU. Either falling-edge triggering or low-level triggering is selected by the IRQE bit
in the OPTION register. IRQ is always configured for level-sensitive triggering at reset.
Connect an external pull-up resistor, typically 4.7 k
, to VDD when IRQ is used in a
level-sensitive wired-OR configuration. Refer to SECTION 5 RESETS AND INTER-
2.7 Non-Maskable Interrupt (XIRQ)
The XIRQ input provides a means of requesting a non-maskable interrupt after reset
initialization. During reset, the X bit in the condition code register (CCR) is set and any
interrupt is masked until MCU software enables it. Because the XIRQ input is level
sensitive, it can be connected to a multiple-source wired-OR network with an external
pull-up resistor to VDD. XIRQ is often used as a power loss detect interrupt.
Whenever XIRQ or IRQ are used with multiple interrupt sources (IRQ must be config-
ured for level-sensitive operation if there is more than one source of IRQ interrupt),
each source must drive the interrupt input with an open-drain type of driver to avoid
contention between outputs. There should be a single pull-up resistor near the MCU
interrupt input pin (typically 4.7 k
). There must also be an interlock mechanism at
each interrupt source so that the source holds the interrupt line low until the MCU rec-
ognizes and acknowledges the interrupt request. If one or more interrupt sources are
still pending after the MCU services a request, the interrupt line will still be held low
and the MCU will be interrupted again as soon as the interrupt mask bit in the condition
code register (CCR) is cleared (normally upon return from an interrupt). Refer to SEC-
EXTAL
4XOUT
MC68HC11F1
NC OR
10 k – 100 k
LOAD
XTAL
EXTAL
SECOND
XTAL
MCU
OSCILLATOR
CIRCUIT OR
CMOS-COMPATIBLE
CLOCK
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
AR215A102K4R CAP CER 1000PF 50V 10% RADIAL
AR201A102K4R CAP CER 1000PF 100V 10% RADIAL
P30G472J1-F CAP CER 4700PF 100V 5% AXIAL
1828857-3 KIT,LC LGTCRP+,JACK 50/125
1828857-2 KIT,LC LGTCRP+,JACK 50/125
相關代理商/技術參數
參數描述
MC68HC11F1CFN5 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1CFU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1CFU1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1CFU3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1CFU4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*