- 您現在的位置：買賣IC網 > PDF目錄45229 > MC68HC11F1CPU4R2 (MOTOROLA INC) 8-BIT, EEPROM, 4 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | MC68HC11F1CPU4R2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, EEPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 14 MM, 1.40 MM HEIGHT, PLASTIC, LQFP-80 |
| 文件頁數： | 116/163頁 |
| 文件大?。?/td> | 711K |
| 代理商： | MC68HC11F1CPU4R2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁當前第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁
MOTOROLA
OPERATING MODES AND ON-CHIP MEMORY
MC68HC11F1
4-18
TECHNICAL DATA
For a description of the bits contained in the CONFIG register refer to 4.3.2.1 CONFIG
4.5 Chip Selects
The function of the chip selects is to minimize the amount of external glue logic needed
to interface the MCU to external devices. The MC68HC11F1 has four software config-
ured chip selects that can be enabled in expanded modes. The chip selects for I/O
(CSIO1 and CSIO2) are used for I/O expansion. The program chip select (CSPROG)
is used with an external memory that contains the program code and reset vectors.
The general-purpose chip select (CSGEN) is the most flexible and is used to enable
external devices.
Such factors as polarity, block size, base address and clock stretching can be con-
trolled using the four chip-select control registers. When a port G pin is not used for
chip select functions it can be used for general-purpose I/O.
When enabled, a chip select signal is asserted whenever the CPU makes an access
to a designated range of addresses. Bus control signals and chip select signals are
synchronous with the external E clock signal. For more information refer to Table A–
7. Expansion Bus Timing in APPENDIX A ELECTRICAL CHARACTERISTICS. The
length of the external E clock cycle to which the external device is synchronized can
be stretched to accommodate devices that are slower than the MCU.
4.5.1 Program Chip Select
The program chip select (CSPROG) is active in the range of memory where the main
program exists. Refer to Figure 4-3.
When enabled, the CSPROG is active during address valid time and is an active-low
signal. Although the general-purpose chip select has priority over the program chip se-
lect, CSPROG can be raised to a higher priority level by setting the GCSPR bit in
CSCTL register. Bits in CSCTL enable the program chip select and determine its ad-
dress range and priority level. Bits in CSSTRH select from zero to three clock cycles
of delay.
4.5.2 I/O Chip Selects
The I/O chip selects (CSIO1 and CSIO2) are fixed in size and fill the remainder of the
4-Kbyte block occupied by the register block. CSIO1 is mapped at $x060–$x7FF and
CSIO2 is mapped at $x800–$xFFF, where “x” corresponds to the high-order nibble of
the register block base address, represented by the value contained in REG[3:0] in the
INIT register.
Bits in the CSCTL register determine the polarity of the active state and enable both I/
O chip selects. Bits in CSGSIZ select whether each chip select is active for address-
valid or E-valid time. Bits in CSSTRH select from zero to three clock cycles of delay.
Refer to Figure 4-3.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11F1CFN5 | 8-BIT, EEPROM, 5 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1CPU4R2 | 8-BIT, EEPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC11F1CFN3 | 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1CFN2 | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1VFN2 | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11F1CPU5 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11F1CPUE5 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC11F1FB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1FB1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1FB3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。