參數資料
型號： MC68HCL05C12AFB
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44
封裝： QFP-44
文件頁數： 140/156頁
文件大小： 756K
代理商： MC68HCL05C12AFB
NON-DISCLOSURE
AGREEMENT
REQUIRED
Serial Peripiheral Interface (SPI)
General Release Specification
MC68HC05C12A — Rev. 3.0
84
Serial Peripiheral Interface (SPI)
MOTOROLA
10.4.4 Slave Select (SS)
The slave select (SS) input line is used to select a slave device. It has to
be low prior to data transactions and must stay low for the duration of the
transaction.
The SS line on the master must be tied high. If it goes low, a mode fault
error flag (MODF) is set in the SPSR.
When CPHA = 0, the shift clock is the OR of SS with SCK. In this clock
phase mode, SS must go high between successive characters in an SPI
message. When CPHA = 1, SS may be left low for several SPI
characters. In cases where there is only one SPI slave MCU, its SS line
could be tied to VSS as long as CPHA = 1 clock modes are used.
10.5 Functional Description
Figure 10-2 shows a block diagram of the serial peripheral interface
circuitry. When a master device transmits data to a slave via the MOSI
line, the slave device responds by sending data to the master device via
the master’s MISO line. This implies full duplex transmission with both
data out and data in synchronized with the same clock signal. Thus, the
byte transmitted is replaced by the byte received and eliminates the
need for separate transmit-empty and receive-full status bits. A single
status bit (SPIF) is used to signify that the I/O operation has been
completed.
The SPI data register (SPDR) is double buffered on read, but not on
write. If a write is performed during data transfer, the transfer occurs
uninterrupted, and the write will be unsuccessful. This condition will
cause the write collision (WCOL) status bit in the SPSR to be set. After
a data byte is shifted, the SPIF flag of the SPSR is set.
In the master mode, the SCK pin is an output. It idles high or low,
depending on the CPOL bit in the SPCR, until data is written to the shift
register, at which point eight clocks are generated to shift the eight bits
of data and then SCK goes idle again.
相關PDF資料
PDF描述
MC68HSC05C12AFB 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP44
MC68HSC05C12AB 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PDIP42
MC68HSC05C12ACP 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PDIP40
MC68HCL05C12AB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP42
MC68HSC05C12CFB 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*