參數資料
型號: MC68HCP11A1CP2
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: HCMOS Single-Chip Microcontroller
中文描述: 8-BIT, 2 MHz, MICROCONTROLLER, PDIP48
封裝: DIP-48
文件頁數: 49/158頁
文件大小: 776K
代理商: MC68HCP11A1CP2
MC68HC11A8
TECHNICAL DATA
SERIAL COMMUNICATIONS INTERFACE
MOTOROLA
5-5
5
5.6 Transmit Data (TxD)
Transmit data is the serial data from the internal data bus which is applied through the
serial communications interface to the output line. The transmitter generates a bit time
by using a derivative of the RT clock, thus producing a transmission rate equal to 1/16
that of the receiver sample clock.
5.7 Functional Description
A block diagram of the SCI is shown in
Figure 5-6
. The user has option bits in serial
communications control register 1 (SCCR1) to determine the “wake-up” method
(WAKE bit) and data word length (M bit) of the SCI. Serial communications control reg-
ister 2 (SCCR2) provides control bits which individually enable/disable the transmitter
or receiver (TE and RE, respectively), enable system interrupts (TIE, TCIE, ILIE) and
provide the wake-up enable bit (RWU) and the send break code bit (SBK). The baud
rate register (BAUD) bits allow the user to select different baud rates which may be
used as the rate control for the transmitter and receiver.
Data transmission is initiated by a write to the serial communications data register
(SCDR). Provided the transmitter is enabled, data stored in the SCDR is transferred
to the transmit data shift register. This transfer of data sets the TDRE bit of the SCI
status register (SCSR) and may generate an interrupt if the transmit interrupt is en-
abled. The transfer of data to the transmit data shift register is synchronized with the
bit rate clock (
Figure 5-7
). All data is transmitted LSB first. Upon completion of data
transmission, the transmission complete (TC) bit of the SCSR is set (provided no
pending data, preamble, or break is to be sent), and an interrupt may be generated if
the transmit complete interrupt is enabled. If the transmitter is disabled, and the data,
preamble, or break (in the transmit shift register) has been sent, the TC bit will also be
set. This will also generate an interrupt if the TCIE bit is set. If the transmitter is dis-
abled in the middle of a transmission, that character will be completed before the trans-
mitter gives up control of the TxD pin.
When the SCDR is read, it contains the last data byte received, provided that the re-
ceiver is enabled. The RDRF bit of the SCSR is set to indicate that a data byte has
been transferred from the input serial shift register to the SCDR, which can cause an
interrupt if the receiver interrupt is enabled. The data transfer from the input serial shift
register to the SCDR is synchronized by the receiver bit rate clock. The OR (over-run),
NF (noise), or FE (framing) error bits of the SCSR may be set if data reception errors
occurred.
An idle line interrupt is generated if the idle line interrupt is enabled and the IDLE bit
(which detects idle line transmission) of SCSR is set. This allows a receiver that is not
in the wake-up mode to detect the end of a message, the preamble of a new message,
or to resynchronize with the transmitter. A valid character must be received before the
idle line condition or the IDLE bit will not be set and an idle line interrupt will not be
generated.
5.8 SCI Registers
There are five registers used in the serial communications interface and the operation
of these registers is discussed in the following paragraphs. Reference should be made
to the block diagram shown in
Figure 5-6
.
相關PDF資料
PDF描述
MC68HCP11A1CP3 HCMOS Single-Chip Microcontroller
MC68HCP11A1MFN2 HCMOS Single-Chip Microcontroller
MC68HCP11A1MP2 HCMOS Single-Chip Microcontroller
MC68HCP11A1VFN2 HCMOS Single-Chip Microcontroller
MC68HCP11A1VP2 HCMOS Single-Chip Microcontroller
相關代理商/技術參數
參數描述
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11E1CFNE2 功能描述:8位微控制器 -MCU 8B MCU 512 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT