8-Bit HCS08 Central Processor Unit (CPU)
40-MHz HCS08 CPU (20-MHz bus)
HC08 instruction set with added BGND instruction
Support for up to 32 interrupt/reset sources
On-Chip Memory
Flash read/program/erase over full operating voltage and
temperature
— MC9S08DZ60 = 60K
— MC9S08DZ48 = 48K
— MC9S08DZ32 = 32K
— MC9S08DZ16 = 16K
Up to 2K EEPROM in-circuit programmable memory;
8-byte single-page or 4-byte dual-page erase sector;
Program and Erase while executing Flash; Erase abort
Up to 4K random-access memory (RAM)
Power-Saving Modes
Two very low power stop modes
Reduced power wait mode
Very low power real time interrupt for use in run, wait,
and stop
Clock Source Options
Oscillator (XOSC) — Loop-control Pierce oscillator;
Crystal or ceramic resonator range of 31.25 kHz to
38.4 kHz or 1 MHz to 16 MHz
Multi-purpose Clock Generator (MCG) — PLL and
FLL modes (FLL capable of 1.5% deviation using
internal temperature compensation); Internal reference
clock with trim adjustment (trimmed at factory, with
trim value stored in ash); External reference with
oscillator/resonator options
System Protection
Watchdog computer operating properly (COP) reset
with option to run from backup dedicated 1-kHz internal
clock source or bus clock
Low-voltage detection with reset or interrupt; selectable
trip points
Illegal opcode detection with reset
Illegal address detection with reset
Flash block protect
Loss-of-lock protection
Development Support
Single-wire background debug interface
On-chip, in-circuit emulation (ICE) with real-time bus capture
Peripherals
ADC — 24-channel, 12-bit resolution, 2.5
μs
conversion time, automatic compare function,
temperature sensor, internal bandgap reference channel
ACMPx — Two analog comparators with selectable
interrupt on rising, falling, or either edge of comparator
output; compare option to xed internal bandgap
reference voltage
MSCAN — CAN protocol - Version 2.0 A, B; standard
and extended data frames; Support for remote frames;
Five receive buffers with FIFO storage scheme; Flexible
identier acceptance lters programmable as: 2 x 32-bit,
4 x 16-bit, or 8 x 8-bit
SCIx — Two SCIs supporting LIN 2.0 Protocol and
SAE J2602 protocols; Full duplex non-return to zero
(NRZ); Master extended break generation; Slave
extended break detection; Wakeup on active edge
SPI — Full-duplex or single-wire bidirectional;
Double-buffered transmit and receive; Master or Slave
mode; MSB-rst or LSB-rst shifting
IIC — Up to 100 kbps with maximum bus loading;
Multi-master operation; Programmable slave address;
General Call Address; Interrupt driven byte-by-byte data
transfer
TPMx — One 6-channel (TPM1) and one 2-channel
(TPM2); Selectable input capture, output compare, or
buffered edge-aligned PWM on each channel
RTC — (Real-time counter) 8-bit modulus counter with
binary or decimal based prescaler; Real-time clock
capabilities using external crystal and RTC for precise
time base, time-of-day, calendar or task scheduling
functions; Free running on-chip low power oscillator
(1 kHz) for cyclic wake-up without external components
Input/Output
53 general-purpose input/output (I/O) pins and 1
input-only pin
24 interrupt pins with selectable polarity on each pin
Hysteresis and congurable pull device on all input pins.
Congurable slew rate and drive strength on all output
pins.
Package Options
64-pin low-prole quad at-pack (LQFP) — 10x10 mm
48-pin low-prole quad at-pack (LQFP) — 7x7 mm
32-pin low-prole quad at-pack (LQFP) — 7x7 mm
MC9S08DZ60 Series Features