參數資料
型號： MCIMX251AVM4
廠商： Freescale Semiconductor
文件頁數： 2/140頁
文件大?。?/td> 0K
描述： IC MPU I.MX25 AUTO 400MAPBGA
標準包裝： 90
系列： i.MX25
核心處理器： ARM9
芯體尺寸： 32-位
速度： 400MHz
連通性： 1 線，CAN，EBI/EMI，以太網，I²C，MMC，智能卡，SPI，SSI，UART/USART，USB OTG
外圍設備： DMA，I²S，POR，PWM，WDT
輸入/輸出數： 128
程序存儲器類型： 外部程序存儲器
RAM 容量： 144K x 8
電壓 - 電源 (Vcc/Vdd)： 1.15 V ~ 1.52 V
數據轉換器： A/D 3x12b
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 400-LFBGA
包裝： 托盤
i.MX25 Applications Processor for Automotive Products, Rev. 10
10
Freescale Semiconductor
MESH_C, MESH_D Wire-mesh tamper detect pins that can be routed at the PCB board to detect attempted tampering of a
protected wire. When security measures are implemented, MESH_C should be pulled-up or connected to
NVCC_DRYICE and triggers a tamper event when floating or when connected to MESH_D. MESH_D
should be pulled-down or connected to GND and triggers an event when floating or connected to
MESH_C. These pins can be left unconnected if the DryIce security features are not being used.
NVCC_DRYICE
This is the DryIce power supply output. The supply source is QVDD when the i.MX25 is in run mode. When
i.MX25 is in reduced power mode, the DryIce supply source is the BATT_VDD supply. This pin can be
used to power external DryIce components (external tamper detect, wire-mesh tamper detect). In order
to guarantee the power-loss protection feature which guarantees that RTC and/or secure keys be
maintained after power-off an external capacitor no less than 4 F must be connected to this supply output
pin. A 4.7 F capacitor is recommended.
OSC_BYP
The 32 kHz oscillator bypass-control pin. If this signal is pulled down, then OSC32K_EXTAL and
OSC32K_XTAL analog pins should be tied to the external 32.768 kHz crystal circuit. If on the other hand
the signal is pulled up, then the external 32 kHz oscillator output clock must be connected to
OSC32K_EXTAL analog pin, and OSC32K_XTAL can be no connect (NC).
OSC32K_EXTAL
OSC32K_XTAL
These analog pins are connected to an external 32 kHz CLK circuit depending on the state of OSC_BYP
pin (see the description of OSC_BYP under the preceding bullet). The 32 kHz reference CLK is required
for normal operation.
POWER_FAIL
An interrupt from PMIC, which should be connected to a low-battery detection circuit. This signal is
internally connected to an on-chip 100 k
Ω pull-down device. If there is no low-battery detection, then users
can tie this pin to GND through a pull-down resistor, or leave the signal as NC. This pin can also be
configured to work as a normal GPIO.
REF
External ADC reference voltage. REF may be tied to GND if the user plans to only use the internally
generated 2.5 V reference supply.
SJC_MOD
Must be externally connected to GND for normal operation. Termination to GND through an external
pull-down resistor (such as 1 k
Ω) is allowed, but the value should be much smaller than the on-chip 100
k
Ω pull-up.
TAMPER_A,
TAMPER _B
DryIce external tamper detect pins, active high. If TAMPER_A or TAMPER_B is connected to
NVCC_DRYICE, then external tampering is detected. These pins can be left unconnected if the DryIce
security features are not being used.
TEST_MODE
For Freescale factory use only. This signal is internally connected to an on-chip pull-down device. Users
must either float this signal or tie it to GND.
UPLL_BYPCLK
Primarily for Freescale factory use. There is no internal on-chip pull-up/down on this pin, so it must be
externally connected to GND or VDD. Aside from factory use, this pin can also be configured (through
muxing) to work as a normal GPIO.
USBPHY1_RREF
Determines the reference current for the USB PHY1 bandgap reference. An external 10 k
Ω 1% resistor to
GND is required.
USBPHY2_DM
USBPHY2_DP
The output impedance of these signals is expected at 10
Ω. It is recommended to also have on-board 33 Ω
series resistors (close to the pins).
Table 4. Signal Considerations (continued)
Signal
Description
相關PDF資料
PDF描述
61819-1111BLF UNIV SERIAL BUS TH LF
LPC1226FBD48/301,1 MCU 32BIT 96K FLASH 8K 48-LQFP
1061541111 ADPT OPT MULTIMODE FC-SC BEIGE
PK30X128VMD100 IC ARM CORTEX MCU 128K 144-MAP
MCHC908JK8CPE IC MCU 8K FLASH 8MHZ 20-DIP
相關代理商/技術參數
參數描述
MCIMX253CJM4 功能描述:處理器 - 專門應用 IMX25 INDUSTRIAL RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX253CJM4A 功能描述:處理器 - 專門應用 IMX25 1.2 INDUST RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX253CVM4 功能描述:處理器 - 專門應用 SENNA IMX25 1.1 INDUSTRIAL RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX253DJM4 功能描述:處理器 - 專門應用 SENNA IMX25 COMM RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX253DJM4A 功能描述:處理器 - 專門應用 IMX25 1.2 COMM RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*