參數資料
型號： MCP1726
廠商： Microchip Technology Inc.
元件分類： 基準電壓源/電流源
英文描述： 1A, Low Voltage, Low Quiescent Current LDO Regulator
中文描述： 1A中，低電壓，低靜態電流LDO穩壓器
文件頁數： 14/30頁
文件大?。?/td> 431K
代理商： MCP1726
MCP1726
DS21936B-page 14
2005 Microchip Technology Inc.
4.0
DEVICE OVERVIEW
The MCP1726 is a high output current, Low Dropout
(LDO) voltage regulator with an adjustable delay
power-good output and shutdown control input. The
low dropout voltage of 220 mV at 1A of current makes
it ideal for battery-powered applications. Unlike other
high output current LDOs, the MCP1726 only draws
220 μA of quiescent current at full load.
4.1
LDO Output Voltage
The MCP1726 LDO is available with either a fixed
output voltage or an adjustable output voltage. The
output voltage range is 0.8V to 5.5V for both versions.
4.1.1
The adjustable version of the MCP1726 uses the ADJ
pin (pin 7) to get the output voltage feedback for output
voltage regulation. This allows the user to set the out-
put voltage of the device with two external resistors.
The nominal voltage for ADJ is 0.41V.
Figure 4-1 shows the adjustable version of the
MCP1726. Resistors R
1
and R
2
form the resistor
divider network necessary to set the output voltage.
With this configuration, the equation for setting V
OUT
is:
ADJUST INPUT
EQUATION 4-1:
FIGURE 4-1:
voltage application circuit.
Typical adjustable output
The allowable resistance value range for resistor R
2
is
from 10 k
Ω
to 200 k
Ω
. Solving the equation for R
1
yields the following equation:
EQUATION 4-2:
4.2
Output Current and Current
Limiting
The MCP1726 LDO is tested and ensured to supply a
minimum of 1A of output current. The MCP1726 has no
minimum output load, so the output load current can go
to 0 mA and the LDO will continue to regulate the
output voltage to within tolerance.
The MCP1726 also incorporates an output current limit.
If the output voltage falls below 0.7V due to an overload
condition (usually represents a shorted load condition),
the output current is limited to 1.7A (typical). If the over-
load condition is a soft overload, the MCP1726 will sup-
ply higher load currents of up to 3A. The MCP1726
should not be operated in this condition continuously as
it may result in failure of the device. However, this does
allow for device usage in applications that have higher
pulsed load currents having an average output current
value of 1A or less.
Output overload conditions may also result in an over-
temperature shutdown of the device. If the junction
temperature rises above 150°C, the LDO will shut
down the output voltage. See
Section 4.9 “Overtem-
perature Protection”
for more information on
overtemperature shutdown.
4.3
Output Capacitor
The MCP1726 requires a minimum output capacitance
of 1 μF for output voltage stability. Ceramic capacitors
are recommended because of their size, cost and
environmental robustness qualities.
Aluminum-electrolytic and tantalum capacitors can be
used on the LDO output as well. The Equivalent Series
Resistance (ESR) of the electrolytic output capacitor
must be no greater than 2 ohms. The output capacitor
should be located as close to the LDO output as is
practical. Ceramic materials X7R and X5R have low
temperature coefficients and are well within the accept-
able ESR range required. A typical 1 μF X7R 0805
capacitor has an ESR of 50 milli-ohms.
Larger LDO output capacitors can be used with the
MCP1726 to improve dynamic performance and power
supply ripple rejection performance. A maximum of
22 μF
is
recommended.
capacitors are not recommended for low-temperature
applications of < -25°C.
Aluminum-electrolytic
V
OUT
V
ADJ
R
------------------
R
2
+
R
2
=
V
OUT
= LDO Output Voltage
V
ADJ
= ADJ Pin Voltage (typically 0.41V)
V
IN
SHDN
GND
PWRGD
C
DELAY
ADJ
V
OUT
1
2
3
4
5
6
7
8
1 μF
V
OUT
4.7 μF
V
IN
On
Off
V
IN
R
1
R
2
C
C2
1000 pF
C
3
MCP1726-ADJ
R
1
R
2
V
--------------------------------
V
–
V
ADJ
=
V
OUT
= LDO Output Voltage
V
ADJ
= ADJ Pin Voltage (typically 0.41V)
相關PDF資料
PDF描述
MCP1727 1.5A, Low Voltage, Low Quiescent Current LDO Regulator
MCP1801 150 mA, High PSRR, Low Quiescent Current LDO
MCP1802 300 mA, High PSRR, Low Quiescent Current LDO
MCP1827T-1202EAB 1.5A, Low Voltage, Low Quiescent Current LDO Regulator
MCP1827-5002EAB 1.5A, Low Voltage, Low Quiescent Current LDO Regulator
相關代理商/技術參數
參數描述
MCP1726-0802E/MF 功能描述:低壓差穩壓器 - LDO 1A .8V Vout Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1726-0802E/SN 功能描述:低壓差穩壓器 - LDO 1A .8V Vout Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1726-1202E/MF 功能描述:低壓差穩壓器 - LDO 1A 1.2V Vout Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1726-1202E/SN 功能描述:低壓差穩壓器 - LDO 1A 1.2V Vout Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
MCP1726-1802E/MF 功能描述:低壓差穩壓器 - LDO 1A 1.8V Vout Extended Temp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*