- 您現在的位置：買賣IC網 > PDF目錄5726 > MCP6033T-E/MC (Microchip Technology)IC OPAMP SNGL 1.8V W/CS 8DFN PDF資料下載
參數資料
| 型號： | MCP6033T-E/MC |
| 廠商： | Microchip Technology |
| 文件頁數： | 9/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP SNGL 1.8V W/CS 8DFN |
| 標準包裝： | 3,300 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.004 V/µs |
| 增益帶寬積： | 10kHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 150µV |
| 電流 - 電源： | 0.9µA |
| 電流 - 輸出 / 通道： | 23mA |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-VFDFN 裸露焊盤 |
| 供應商設備封裝： | 8-DFN（2x3） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MCP6033T-E/MCTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
2008 Microchip Technology Inc.
DS22041B-page 17
MCP6031/2/3/4
4.9
Application Circuits
4.9.1
BATTERY CURRENT SENSING
The MCP6031/2/3/4 op amps’ Common Mode Input
Range, which goes 0.3V beyond both supply rails,
supports their use in high side and low side battery
current sensing applications. The ultra low quiescent
current (0.9 A, typical) helps prolong battery life, and
the rail-to-rail output supports detection of low currents.
Figure 4-7 shows a high side battery current sensor
circuit. The 10
Ω resistor is sized to minimize power
losses. The battery current (IDD) through the 10Ω
resistor causes its top terminal to be more negative
than the bottom terminal. This keeps the common
mode input voltage of the op amp below VDD, which is
within its allowed range. The output of the op amp will
also be below VDD, which is within its Maximum Output
Voltage Swing specification.
FIGURE 4-7:
High Side Battery Current
Sensor.
4.9.2
PRECISION COMPARATOR
Use high gain before a comparator to improve the lat-
ter’s input offset performance. Figure 4-8 shows a gain
of 11 V/V placed before a comparator. The reference
voltage VREF can be any value between the supply
rails.
FIGURE 4-8:
Precision, Non-inverting
Comparator.
4.9.3
DRIVING MCP3421
ΔΣ A/D
CONVERTER
A RSH and CSH snubber reduces the output impedance
of MCP6031 op amp, which reduces the gain error
caused by switching transients, which occur at the
MCP3421 ADC's sampling rate. The snubber also
maintains feedback stability and avoids AC response
peaking and step response overshoot and ringing
(caused by the op amp’s inductive output impedance
resonating with the ADC’s input capacitance). The cost
for this improvement is low. Best of all, using an op amp
with higher supply current is avoided. See Figure 4-9.
This figure also includes a resistor to balance the
impedance at the ADC's inputs (RBAL) at the sampling
frequency; it may not be needed in all designs.
FIGURE 4-9:
Driving the MCP3421 using
an R-C Snubber.
VDD
IDD
MCP6031
100 k
Ω
1M
Ω
1.4V
VOUT
10
Ω
to
5.5V
I
DD
V
DD
V
OUT
–
10 V/V
() 10
Ω
()
------------------------------------------
=
VIN
1M
Ω
VOUT
MCP6031
100 k
Ω
MCP6541
VREF
VIN
MCP6031
RSH
CSH
1.00 k
Ω
2.2 F
RBAL
1.00 k
Ω
MCP3421
ΔΣ
1.00 k
Ω
ZIND
2.25 M
Ω
相關PDF資料 |
PDF描述 |
|---|---|
| MCP6033-E/SN | IC OPAMP SNGL 1.8V W/CS 8SOIC |
| 2037-09-C | GAS DISCHARGE TUBE MINI 2 POLE |
| MCP6033T-E/SN | IC OPAMP SNGL 1.8V W/CS 8SOIC |
| SCW-SC3LF-500R-F | RES 500 OHM 3W 1% 2512 WIDE |
| MCP6033T-E/MS | IC OPAMP SNGL 1.8V W/CS 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP6034 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 uA, High Precision Op Amps |
| MCP6034-E/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 μA, High Precision Op Amps |
| MCP6034E/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 uA, High Precision Op Amps |
| MCP6034-E/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 μA, High Precision Op Amps |
| MCP6034-E/OT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:0.9 μA, High Precision Op Amps |
發布緊急采購，3分鐘左右您將得到回復。