OPERATIONAL MODES RECOVERY CONDITION The SB" />
參數資料
型號: MCZ33742SEG
廠商: Freescale Semiconductor
文件頁數: 39/71頁
文件大?。?/td> 0K
描述: IC SYSTEM BASIS CHIP CAN 28-SOIC
標準包裝: 26
應用: 自動
電流 - 電源: 42mA
電源電壓: 5.5 V ~ 18 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 28-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 28-SOIC W
包裝: 管件
Analog Integrated Circuit Device Data
44
Freescale Semiconductor
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
RECOVERY CONDITION
The SBC will try to recover from a bus fault condition by sampling for a correct low level at TXD, as illustrated in Figure 26.
As soon as an RXD permanent recessive is detected, the RXD driver is deactivated and a weak pull-down current source is
activated in order to allow recovery conditions. The driver stays disabled until the failure is cleared (RXD no longer permanent
recessive) and the bus driver is activated by an SPI register command (write 1 to the CANCLR bit in the CAN register).
Figure 26. RXD Recovery Conditions
TXD PERMANENT DOMINANT FAILURE
PRINCIPLE
In the event TXD is set to a permanent low level, the CAN bus is set into dominant level, and no communication is possible.
The SBC has a TXD permanent timeout detector. After timeout, the bus driver is disabled and the bus is released in a recessive
state. The TXD permanent dominant failure is reported in the TIM1 register.
RECOVERY
The TXD permanent dominant is used and activated also in case of TXD short to RXD. The recovery condition for TXD
permanent dominant (recovery means the reactivation of the CAN drivers) is done by an SPI command and is controlled by the
MCU.
The driver stays disabled until the failure is cleared (TXD no longer permanent dominant) and the bus driver is activated by
an SPI register command (write logic [1] to CANCLR bit in the CAN register).
TXD TO RXD SHORT CIRCUIT FAILURE
PRINCIPLE
In the event the TXD is shorted to RXD when an incoming CAN message is received, the RXD will be at a LOW. Consequently,
the TXD pin is LOW and drives CANH and CANL into the dominant state. The bus is stuck in dominant mode and no further
communication is possible.
DETECTION AND RECOVERY
The TXD permanent dominant timeout will be activated and release the CANL and CANH drivers. However, at the next
incoming dominant bit, the bus will be stuck again in dominant. In order to avoid this situation, the recovery from a failure
(recovery means the reactivation of the CAN drivers) is done by an SPI command and controlled by the MCU.
INTERNAL ERROR OUTPUT FLAGS
There are internal error flags to signal whenever thermal protection is activated or over-current detection occurs on the CANL
or CANH pins (THERM-CUR bit). The errors are reported in the CAN register.
CANL
Diff Output
RXD Output
RXD Short to VDD
RXD Flag
RXD Flag Latched
Sampling
Note RXD Flag is neither the RXPR bit in the LPC register
RXD no longer shorted to VDD
CANH
nor the CANF bit in INTR register.
相關PDF資料
PDF描述
EEM28DRYN CONN EDGECARD 56POS DIP .156 SLD
837975-3 LGH-3 LEAD ELECT MLD END
S1210R-101K INDUCTOR SHIELDED .10UH SMD
MCZ33689DEWR2 IC SYSTEM BASIS CHIP LIN 32-SOIC
EEM28DRYH CONN EDGECARD 56POS DIP .156 SLD
相關代理商/技術參數
參數描述
MCZ33742SEGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33780EG 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MCZ33780EG 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC
MCZ33780EGR2 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MCZ33781EK 功能描述:輸入/輸出控制器接口集成電路 DBUS2 MASTER STND RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray