參數資料
型號： MCZ33797EK
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Four Channel Squib Driver IC
中文描述： 四通道爆管驅動IC
文件頁數： 20/34頁
文件大?。?/td> 290K
代理商： MCZ33797EK
Analog Integrated Circuit Device Data
Freescale Semiconductor
20
33797
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
TX: Request loop-to-loop short command ($E0–$E3)
RX: Previous executed command information.
TX: Request another command sequence.
RX: Receive loop-to-loop results from test.
CROSS-COUPLED SQUIB IC FUNCTION
The cross-coupled application utilizes the high- and low-
side squib drivers from two different squib driver ICs (see
Figure 9
, Cross-Coupled Squib Firing, page
18
.) Through the
SPI interface, the squib IC will maintain the capability to
conduct standard diagnostics (short-to-battery, short-to-
ground, short between squibs, and squib diagnostics)
between two different squib ICs. The squib IC must maintain
the capability to fire the squib drivers with the ARM and FIRE
command in either cross-coupled or single IC applications.
When the firing squib driver IC is used in cross-coupled
applications, the low-side squib driver must be activated prior
to activating the high-side squib driver.
Cross-coupling the high- and low-side squib driver from
two different squib driver ICs must be done without interfering
with standard squib operations when the squib IC is used in
an application where the high- and low-side squib drivers are
located on the same IC.
All remaining diagnostic functions will operate standard in
either a cross-coupled or single IC applications. These
functions include R
R_
DIAG
, R
R_
LIMIT_X
, High side, V
VFIRE_XX
,
V
VFIRE_
RTN
, V
TRANSTX
, squib current timing measurement,
and FEN_1 and FEN_2 diagnostics.
The SENSE_1A (1B, 2A, or 2B) pin squib IC #1 is
connected to SQB_LO_1A (1B, 2A, or 2B) pin squib driver
IC #2 and is used to feed the diagnostic signal for
determining squib resistance and short-to-battery ground
conditions (see
Figure 9
, page
18
). During a fire event, the
fire current passes from squib driver IC #1 high-side driver
though the squib to squib driver IC #2 low-side driver. In the
cross-coupled mode, the squib driver IC #2 $C2
(SQUIB_LO_1A_CONT, [1B, 2A, or 2B]) command will be
used to check continuity of the low-side driver from the
SQB_LO_1A (1B, 2A, or 2B) pin to the low-side driver FET.
The low-side driver continuity is checked during the
continuity test. The driver continuity information will be
cleared after the information is transmitted on the next valid
SPI command.
EXAMPLE—CROSS-COUPLED SQUIB COMMAND
SPI SEQUENCE FROM MICROCONTROLLER
TX: Squib IC #1 request squib 1A resistance measurement
($D0).
RX: Previous executed command information.
TX: Run another command on the same squib IC #1.
RX: Receive measured squib 1A resistance information.
TX: Squib IC #1 request continuity command ($C2).
RX: Previous executed command information.
TX: Squib IC #2 request continuity command ($C2).
RX: Previous executed command information.
TX: Squib IC #2 request continuity command ($C2).
RX: Receive low-side driver continuity information for low-
side drivers which reside on IC #2.
TX: Squib IC #1 request another command sequence.
RX: Receive low-side driver continuity information for low-
side drivers that reside on IC #1.
TX: Squib IC #1 request loop-to-loop short command
($E0–$E3)
RX: Previous executed command information.
TX: Squib IC #2 request loop to loop short command for
other ICs ($E8).
RX: Previous executed command information.
TX: Squib IC #2 request loop-to-loop short command for
other ICs ($E8).
RX: Receive loop-to-loop results from test run on IC #1.
TX: Squib IC #1 request another command sequence.
RX: Receive loop-to-loop results from test run on IC #1.
FIRING A SQUIB
The firing of a squib driver requires the FEN_1 and FEN_2
pins to be high and two separate 8-bit writes be made to the
shift register. With FEN_1 pin high, squibs 1A and 1B can be
armed and fired. With FEN_2 pin high, squibs 2A and 2B can
be armed and fired. The first write is to ARM squib drivers in
preparation of receiving the fire command. Squib
1A and
squib
1B can be armed separately from squib
2A and
squib
2B (refer to
Table 6
) or all squibs can be fired at once
(refer to
Table 7
). All ARM and 5X (Fire) commands will be
echoed back on the SPI Data output.
相關PDF資料
PDF描述
MCZ33800EK Engine Control Integrated Circuit
MCZ33879AEK Configurable Octal Serial Switch with Open Load Detect Current Disable
MCZ33880EG Configurable Octal Serial Switch with Serial Peripheral Interface I/O
MCZ33883EG H-Bridge Gate Driver IC
MCZ33884EG Switch Monitor Interface
相關代理商/技術參數
參數描述
MCZ33797EKR2 功能描述:功率驅動器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
MCZ33800EK 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33800EKR2 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33800R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit
MCZ33810EK 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*