- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33993EW (飛思卡爾半導體(中國)有限公司) Multiple Switch Detection Interface PDF資料下載
參數資料
| 型號： | MCZ33993EW |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Multiple Switch Detection Interface |
| 中文描述： | 多交換檢測接口 |
| 文件頁數： | 22/28頁 |
| 文件大小： | 504K |
| 代理商： | MCZ33993EW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
22
33993
TYPICAL APPLICATIONS
INTRODUCTION
Figure 14. MOSFET or LED Driver Output
The sequence of commands (from Normal mode with
inputs tri-state) required to set up the device to drive a
MOSFET are as follows:
wetting current timer enable command
– Disable SPn
wetting current timer (refer to
Table 8
, page
14
)
metallic command
– Set SPn to 16 mA or 2.0 mA gate
drive current (refer to
Table 7
, page
14
)
settings command
– Set SPn as switch-to-battery (refer
to
Table 5
, page
13
)
tri-state command
– Disable tri-state for SPn (refer to
Table 9
, page
14
)
After the
tri-state command
has been sent (tri-state
disable), the MOSFET gate will be pulled to ground. From this
point forward the MOSFET may be turned on and off by
sending the
settings command
:
settings command
– SPn as switch-to-ground
(MOSFET ON)
settings command
– SPn as switch-to-battery
(MOSFET OFF)
Monitoring of the MOSFET drain in the OFF state provides
open load detection. This is done by using an SGn input
comparator. With the SGn input in tri-state, the load will pull
up the SGn input to battery. With open load the SGn pin is
pulled down to ground through an external resistor. The open
load is indicated by a logic [1] in the SO data bit.
The
analog command
may be used to monitor the drain
voltage in the MOSFET ON state. By sourcing 2.0 mA of
current to the 1.5 k
resistor, the analog voltage on the SGn
pin will be approximately:
As the voltage on the drain of the MOSFET increases, so
does the voltage on the SGn pin. With the SGn pin selected
as analog, the MCU may perform the A / D conversion.
Using this method for controlling unclamped inductive
loads is not recommended. Inductive flyback voltages greater
than V
PWR
may damage the IC.
The SP0 – SP7 pins of this device may also be used to
send signals from one module to another. Operation is similar
to the gate control of a MOSFET.
For LED applications a resistor in series with the LED is
recommended but not required. The switch-to-ground inputs
are recommended for LED application. To drive the LED use
the following commands:
wetting current timer enable command
– Disable SGn
wetting current timer
metallic command
– Set SGn to 16 mA
From this point forward the LED may be turned on and off
using the
tri-state command
:
tri-state command
– Disable tri-state for SGn (LED ON)
tri-state command
– Enable tri-state for SGn (LED OFF)
These parameters are easily programmed via SPI
commands in Normal mode.
MULTIPLE 33993 DEVICES IN A MODULE SYSTEM
Connecting power to the 33993 and the MCU for Sleep
mode operation may be done in several ways.
Table 20
shows several system configurations for power between the
MCU and the 33993 and their specific requirements for
functionality.
Multiple 33993 devices may be used in a module system.
SPI control may be done in parallel or serial. However when
parallel mode is used, each device is addressed
independently (refer to
MCU Interface Description
, page
11
).
Therefore when sending the
sleep command
,
one device will
enter sleep before the other. For multiple devices in a system,
it is recommended that the devices are controlled in serial (S0
SP0
SG0
SG13
16
mA
2.0
mA
4.0 V Ref
+
-
Comparator
To SPI
V
PWR
SG0
1.5 k
L
VBAT
AMUX
100 k
V
PWR
+
-
Comparator
2.0 mA
To SPI
4.0 V
Ref
2.0
mA
16
mA
16
mA
V
PWR
V
PWR
SG0
16
mA
2.0
mA
V
PWR
V
PWR
+
-
Comparator
To SPI
4.0 V Ref
SG13
Table 20. Sleep Mode Power Supply
MCU
V
DD
33993
V
DD
Comments
5.0 V
5.0 V
All wake-up conditions apply. (Refer to
Sleep Mode
,
page
17
.)
5.0 V
0 V
SPI wake-up is not possible.
0 V
5.0 V
Sleep mode not possible. Current from
CS
pull up will
flow through MCU to V
that has been switched off.
Negative edge of
CS
will put 33993 in Normal mode.
0 V
0 V
SPI wake-up is not possible.
V
SGn
= I
SGn
x 1.5 k
+ V
DS
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33996EK | 16-Output Switch with SPI Control |
| MCZ34652EF | 2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability |
| MCZ34701EWR2 | 1.5A Switch-Mode Power Supply with Linear Regulator |
| MCZ79076EG | Electronic Ignition Control Circuit |
| MD-S5007 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33993EWR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33996CEK | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Bulk |
| MCZ33996CEKR2 | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Tape and Reel |
| MCZ33996EK | 功能描述:開關變換器、穩壓器與控制器 16 LOW SIDE SW RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MCZ33996EK | 制造商:Freescale Semiconductor 功能描述:IC LOAD SWITCH 27V 32SOIC |
發布緊急采購，3分鐘左右您將得到回復。