參數資料
型號： MCZ33993EW
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Multiple Switch Detection Interface
中文描述： 多交換檢測接口
文件頁數： 9/28頁
文件大小： 504K
代理商： MCZ33993EW
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
33993
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33993 device is an integrated circuit designed to
provide systems with ultra-low quiescent sleep wake-up
modes and a robust interface between switch contacts and a
microprocessor. The 33993 replaces many of the discrete
components required when interfacing to microprocessor-
based systems while providing switch ground offset
protection, contact wetting current, and system wake-up.
The 33993 features 8-programmable switch-to-ground or
switch-to-battery inputs and 14 switch-to-ground inputs. All
switch inputs may be read as analog inputs through the
analog multiplexer (AMUX). Other features include a
programmable wake-up timer, programmable interrupt timer,
programmable wake-up /interrupt bits, and programmable
wetting current settings.
This device is designed primarily for automotive
applications but may be used in a variety of other applications
such as computer, telecommunications, and industrial
controls.
FUNCTIONAL PIN DESCRIPTION
CHIP SELECT (CS)
The system MCU selects the 33993 to receive
communication using the chip select (CS) pin. With the CS in
a logic low state, command words may be sent to the 33993
via the serial input (SI) pin, and switch status information can
be received by the MCU via the serial output (SO) pin. The
falling edge of CS enables the SO output, latches the state of
the INT pin, and the state of the external switch inputs.
Rising edge of the CS initiates the following operation:
1. Disables the SO driver (high impedance)
2. INT pin is reset to logic [1], except when additional
switch changes occur during CS low. (See
Figure 6
.)
Activates the received command word, allowing the 33993
to act upon new data from switch inputs.
To avoid any spurious data, it is essential the high-to-low
and low-to-high transitions
of the CS signal occur only when
SCLK is in a logic low state. Internal to the 33993 device is an
active pull-up to V
DD
on the CS.
In Sleep mode the negative edge of the CS (V
DD
applied)
will wake up the 33993 device. Data received from the device
during CS wake-up may not be accurate.
SERIAL CLOCK (SCLK)
The system clock (SCLK) pin clocks the internal shift
register of the 33993. The SI data is latched into the input
shift register on the falling edge of SCLK signal. The SO pin
shifts the switch status bits out on the rising edge of SCLK.
The SO data is available for the MCU to read on the falling
edge of SCLK. False clocking of the shift register must be
avoided to ensure validity of data. It is essential the SCLK pin
be in a logic low state whenever CS makes any transition. For
this reason, it is recommended, though not necessary, that
the SCLK pin is commanded to a low logic state as long as
the device is not accessed and CS is in a logic high state.
When the CS is in a logic high state, any signal on the SCLK
and SI pins will be ignored and the SO pin is tri-state.
SPI SLAVE IN (SI)
The SI pin is used for serial instruction data input. SI
information is latched into the input register on the falling
edge of SCLK. A logic high state present on SI will program
a
one
in the command word on the rising edge of the CS
signal. To program a complete word, 24 bits of information
must be entered into the device.
SPI SLAVE OUT (SO)
The SO pin is the output from the shift register. The SO pin
remains tri-stated until the CS pin transitions to a logic low
state. All
open switches
are reported as
zero
, all
closed
switches
are reported as
one
. The negative transition of CS
enables the SO driver.
The first positive transition of SCLK will make the status
data bit 24 available on the SO pin. Each successive positive
clock will make the next status data bit available for the MCU
to read on the falling edge of SCLK. The SI SO shifting of the
data follows a first-in-first-out protocol, with both input and
output words transferring the most significant bit (MSB) first.
INTERRUPT (INT)
The INT pin is an interrupt output from the 33993 device.
The INT pin is an open-drain output with an internal pull-up to
V
DD
. In Normal mode, a switch state change will trigger the
INT pin (when enabled). The INT pin and INT bit in the SPI
register are latched on the falling edge of CS. This permits
the MCU to determine the origin of the interrupt. When two
33993 devices are used, only the device initiating the
interrupt will have the INT bit set. The INT pin is cleared on
the rising edge of CS. The INT pin will not clear with rising
edge of CS if a switch contact change has occurred while CS
was low.
In a multiple 33993 device system with WAKE high and
V
DD
on (Sleep mode), the falling edge of INT will place all
33993s in Normal mode.
相關PDF資料
PDF描述
MCZ33996EK 16-Output Switch with SPI Control
MCZ34652EF 2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability
MCZ34701EWR2 1.5A Switch-Mode Power Supply with Linear Regulator
MCZ79076EG Electronic Ignition Control Circuit
MD-S5007 Analog IC
相關代理商/技術參數
參數描述
MCZ33993EWR2 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MCZ33996CEK 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Bulk
MCZ33996CEKR2 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Tape and Reel
MCZ33996EK 功能描述:開關變換器、穩壓器與控制器 16 LOW SIDE SW RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MCZ33996EK 制造商:Freescale Semiconductor 功能描述:IC LOAD SWITCH 27V 32SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*