參數資料
型號: MF280C51-30D
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP44
封裝: QFP-44
文件頁數: 12/176頁
文件大小: 2962K
代理商: MF280C51-30D
109
2535J–AVR–08/10
ATtiny13
The minimum period for the Serial Clock Input (SCI) during High-voltage Serial Programming is
220 ns.
17.7.1
High-Voltage Serial Programming Algorithm
To program and verify the ATtiny13 in the High-voltage Serial Programming mode, the following
sequence is recommended (See instruction formats in Table 17-13 on page 110):
The following algorithm puts the device in High-voltage Serial Programming mode:
1. Set Prog_enable pins listed in Table 17-11 to “000”, RESET pin to “0” and Vcc to 0V.
2. Apply 4.5 - 5.5V between VCC and GND. Ensure that Vcc reaches at least 1.8V within
the next 20s.
3. Wait 20 - 60s, and apply 11.5 - 12.5V to RESET.
4. Keep the Prog_enable pins unchanged for at least 10s after the High-voltage has
been applied to ensure the Prog_enable Signature has been latched.
5. Release the Prog_enable[2] pin to avoid drive contention on the Prog_enable[2]/SDO
pin.
6. Wait at least 300s before giving any serial instructions on SDI/SII.
7. Exit Programming mode by power the device down or by bringing RESET pin to 0V.
If the rise time of the Vcc is unable to fulfill the requirements listed above, the following alterna-
tive algorithm can be used.
1. Set Prog_enable pins listed in Table 17-11 to “000”, RESET pin to “0” and Vcc to 0V.
2. Apply 4.5 - 5.5V between VCC and GND.
3. Monitor Vcc, and as soon as Vcc reaches 0.9 - 1.1V, apply 11.5 - 12.5V to RESET.
4. Keep the Prog_enable pins unchanged for at least 10s after theHigh-voltage has been
applied to ensure the Prog_enable Signature has been latched.
5. Release the Prog_enable[2] pin to avoid drive contention on the Prog_enable[2]/SDO
pin.
Table 17-10. Pin Name Mapping
Signal Name in High-voltage
Serial Programming Mode
Pin Name
I/O
Function
SDI
PB0
I
Serial Data Input
SII
PB1
I
Serial Instruction Input
SDO
PB2
O
Serial Data Output
SCI
PB3
I
Serial Clock Input (min. 220ns period)
Table 17-11. Pin Values Used to Enter Programming Mode
Pin
Symbol
Value
SDI
Prog_enable[0]
0
SII
Prog_enable[1]
0
SDO
Prog_enable[2]
0
相關PDF資料
PDF描述
MR80C32E-16P883 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44
MR80C32E-16P883 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44
MQ83C154DCXXX-25P883D 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
MR80C52EXXX-25:RD 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
MIP7365-450F17I 64-BIT, 450 MHz, MICROPROCESSOR, CQFP208
相關代理商/技術參數
參數描述
MF283C151C-12 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MF283C151C-16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MF283C151C-20 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MF283C151C-25 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MF283C151C-30 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller