- 您現在的位置：買賣IC網 > PDF目錄377972 > ML6599 (Fairchild Semiconductor Corporation) Hot-Insertable Active SCSI Terminator(熱插入有源SCSI終端器) PDF資料下載
參數資料
| 型號： | ML6599 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Hot-Insertable Active SCSI Terminator(熱插入有源SCSI終端器) |
| 中文描述： | 熱可插入主動SCSI端接（熱插入有源的SCSI終端器） |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 83K |
| 代理商： | ML6599 |
ML6599
4
REV. 1.0 10/25/2000
Functional Description
SCSI terminators are used to decrease the transmission
line effects of SCSI cable. Termination must be provided
at the beginning and end of the SCSI bus to ensure that
data errors due to reflections on the bus are eliminated.
With the increasing use of higher data rates and cable
lengths in SCSI subsystems, active termination has
become necessary. Active termination also minimizes
power dissipation and can be activated or deactivated
under software control, thus eliminating the need for end
user intervention. The V-I characteristics of popular SCSI
termination schemes are shown in Figure 1. Theoretically,
the desired V-I characteristics are the Boulay type for
signal assertion (high to low) and the ideal type for signal
negation (low to high). The ML6599 with its MOSFET-
based nonlinear termination element provides the most
optimum V-I characteristics for both signal assertion and
negation.
IDEAL
ML6599
BOULAY
220/330
2.85V
2.7V
2.5V
0.2V
TERMINATOR (SOURCE)
DRIVER (SINK)
20mA
40mA
24mA
48mA
V
I
Figure 1. V-1 Characteristics of Various
SCSI Termination Schemes
The ML6599 provides active termination for 9 signal lines,
thus accommodating basic SCSI which requires 9 lines to
be terminated. When used with the ML6599, wide SCSI,
which requires 27, 36 or 45 lines to be terminated, can
also be accommodated. The ML6599 integrates an
accurate voltage reference (1V dropout voltage) and 9
MOSFET-based termination lines. A single internal resistor
is trimmed to tune the V-I characteristic of the MOSFETs.
The voltage reference circuit produces a precise 2.85V
level and is capable of sourcing 24mA into each of the
nine terminating lines when low (active). When the signal
line is negated (driver turns off), the terminator pulls the
signal line back to 2.85V. The regulator will source
200mA and sink 100mA while maintaining regulation of
2.85V.
The ML6599 SCSI terminator provides an active low
control signal (
DISCNKT
) which has an internal 200ky
pull-up resistor. The
DISCNKT
input isolates the ML6599
from the signal lines and effectively removes the
terminator from the SCSI bus with a disconnect mode
current of less than 100μA when pulled low. In addition,
the ML6599 provides for negative clamping of signal
transients and also supports current sink capability in
excess of 10mA per signal line to handle active negation
driver overshoot above 2.85V, a common occurrence with
SCSI transceivers.
Disconnect mode capacitance is a very critical parameter
in SCSI systems. The ML6599 provides a capacitance
contribution of only 5pF.
Hot-insertability
“Hot” insertion of a SCSI device refers to the act of
plugging a SCSI device which is initially unpowered into
a powered SCSI bus. The SCSI device subsequently draws
power from the TERMPWR line during its startup routine
and thereafter. “Hot” removal refers to the act of
removing a powered SCSI device from a powered SCSI
bus. A device which performs both tasks with no physical
damage to itself or other devices on the bus, nor which
alters the existing state of the bus by drawing excessive
currents, is termed “hot-swappable.”
The ML6599 hot-insertable SCSI terminator typically
draws 1μA from any given output line (L1–L9) during a
hot-insertion/removal procedure, thereby protecting itself
and preserving the state of the bus. The low insertion
current is achieved by effectively shorting the gate to
drain of the output PMOS device until the 2.85V
reference (V
REF
) has powered up. A second PMOS in
series with a Schottky diode is used as the shorting bypass
device. After V
REF
reaches a sufficient level, the bypass
device is turned off and the part operates normally. Figure
2 gives an application diagram showing a typical SCSI
bus configuration. To ensure proper operation, the
TERMPWR pin must be connected to the SCSI
TERMPOWER line. As outlined in Annex G of the ANSI
SCSI-3 Parallel Interface Specification (X3T9.2/855D),
“The SCSI bus termination shall be external to the device
being inserted or removed.” In other words, any terminator
相關PDF資料 |
PDF描述 |
|---|---|
| ML65F16244 | 16-Bit Buffer/Line Driver with 3-State Outputs(16位緩沖器/線驅動器（三態輸出）) |
| ML65F16245 | 16-Bit Bidirectional Transceiver with 3-State Outputs(16位雙向收發器（三態輸出）) |
| ML66517 | 16-Bit Microcontroller |
| ML670100 | OKIs High-Performance CMOS 32-Bit Single Chip Microcontroller |
| ML671000 | CMOS 32-Bit Single-Chip Microcontroller with Built-in USB Device Controller(內置USB設備控制器的32位單芯片微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML6599CS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Hot-Insertable Active SCSI Terminator |
| ML6599CT | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Hot-Insertable Active SCSI Terminator |
| ML65A30MB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ML65 Series DC-DC Converter |
| ML65A30ML | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ML65 Series DC-DC Converter |
| ML65A30MR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ML65 Series DC-DC Converter |
發布緊急采購，3分鐘左右您將得到回復。