- 您現在的位置：買賣IC網 > PDF目錄377973 > ML9092-04 (OKI SEMICONDUCTOR CO., LTD.) LCD Driver with Key Scanner and RAM PDF資料下載
參數資料
| 型號： | ML9092-04 |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | LCD Driver with Key Scanner and RAM |
| 中文描述： | 液晶顯示驅動器，掃描器和RAM的關鍵 |
| 文件頁數： | 52/66頁 |
| 文件大?。?/td> | 659K |
| 代理商： | ML9092-04 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
FEDL9092-01
OKI Semiconductor
ML9092-01/02/03/04
52/66
3) Parallel-in/Serial-out Shift Register
The KREQ signal goes to a low level when the rotary encoder read instruction is executed, when the
UP/DOWN counter will be reset to “0”.
CS
Figure 8 Operation of KREQ Output
Notes:
1. The KREQ signal is output by a logical OR of the KREQ signal generated by a key scan and the
KREQ signal generated by the rotary encoder. The KREQ signal from the rotary encoder is reset by
executing the rotary encoder read instruction; however, the KREQ signal generated by a key scan is
not reset even if the key scan register read instruction is executed. Also, if the KREQ signal is
generated by a key scan, it will not be reset even if the rotary encoder read instruction is executed.
Although dependent on the components glued to this LSI, it is recommended that the rotary encoder
read instruction and key scan register read instruction be executed as a set when the KREQ signal
goes to a “H” level.
2. The maximum read cycle time for when the KREQ signal is at a “H” level is practically determined by
the signal input from the rotary encoder and the 3-bit counter built into this LSI. Therefore, make the
time taken before starting to execute the rotary encoder read instruction 12 ms or less.
3. Using a rotary encoder switch that has the click stabilizing points shown below is recommended.
Click stabilizing points
A signal
B signal
Waveform of a Recommended Rotary Encoder Switch
CP
DI/O
1
2
8
9
11
10
12
13
14
15
16
Instruction code
READ DATA1
Output state
Input state
KREQ
相關PDF資料 |
PDF描述 |
|---|---|
| ML9203 | 5 x 7 Dot Character x 16-Digit x 2-Line Display Controller/Driver with Character RAM |
| ML9203-xx | 5 x 7 Dot Character x 16-Digit x 2-Line Display Controller/Driver with Character RAM |
| ML9204 | 5 X 7 Dot Character ?24-Digit ?2-Line Display Controller/Driver with Character RAM (Built-in Key Scan) |
| ML9204-xx | 5 X 7 Dot Character ?24-Digit ?2-Line Display Controller/Driver with Character RAM (Built-in Key Scan) |
| ML9205-01 | 5 x 7 Dot Character x 16-Digit Display Controller/Driver with Character RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML9092-04TB | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:LCD Driver with Key Scanner and RAM |
| ML9093F | 制造商:Ohmite Mfg Co 功能描述: |
| ML912 | 制造商:AEMC Instruments 功能描述:DATA LOGGER, 100A-1000AAC, 2CH, Input Voltage:- , RoHS Compliant: NA |
| ML914 | 制造商:AEMC Instruments 功能描述:DATA LOGGER, 100A-1000AAC, 4CH; Input Voltage:- ;RoHS Compliant: NA |
| ML9203 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 x 7 Dot Character x 16-Digit x 2-Line Display Controller/Driver with Character RAM |
發布緊急采購，3分鐘左右您將得到回復。