- 您現在的位置：買賣IC網 > PDF目錄4048 > MPC745CPX350LE (Freescale Semiconductor)MCU HIP4DP 350MHZ 255-PBGA PDF資料下載
參數資料
| 型號： | MPC745CPX350LE |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 39/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU HIP4DP 350MHZ 255-PBGA |
| 標準包裝： | 60 |
| 系列： | MPC7xx |
| 處理器類型： | 32-位 MPC7xx PowerPC |
| 速度： | 350MHz |
| 電壓： | 2V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 255-BBGA，F(xiàn)CBGA |
| 供應商設備封裝： | 255-FCPBGA（21x21） |
| 包裝： | 托盤 |
MPC755 RISC Microprocessor Hardware Specifications, Rev. 8
44
Freescale Semiconductor
System Design Information
There is no standardized way to number the COP header shown in Figure 24; consequently, many different
pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in
Figure 25 is common to all known emulators.
The QACK signal shown in Figure 24 is usually connected to the PCI bridge chip in a system and is an
input to the MPC755 informing it that it can go into the quiescent state. Under normal operation this occurs
during a low-power mode selection. In order for COP to work, the MPC755 must see this signal asserted
(pulled down). While shown on the COP header, not all emulator products drive this signal. If the product
does not, a pull-down resistor can be populated to assert this signal. Additionally, some emulator products
implement open-drain type outputs and can only drive QACK asserted; for these tools, a pull-up resistor
can be implemented to ensure this signal is deasserted when it is not being driven by the tool. Note that the
pull-up and pull-down resistors on the QACK signal are mutually exclusive and it is never necessary to
populate both in a system. To preserve correct power-down operation, QACK should be merged via logic
so that it also can be driven by the PCI bridge.
8.8
Thermal Management Information
This section provides thermal management information for air-cooled applications. Proper thermal control
design is primarily dependent on the system-level design—the heat sink, airflow, and thermal interface
material. To reduce the die-junction temperature, heat sinks may be attached to the package by several
methods—adhesive, spring clip to holes in the printed-circuit board or package, and mounting clip and
screw assembly; see Figure 25. This spring force should not exceed 5.5 pounds (2.5 kg) of force.
Figure 25 describes the package exploded cross-sectional view with several heat sink options.
Figure 25. Package Exploded Cross-Sectional View with Several Heat Sink Options
Adhesive or
Thermal Interface Material
Heat Sink
CBGA Package
Heat Sink
Clip
Printed-Circuit Board
Option
相關PDF資料 |
PDF描述 |
|---|---|
| MPC745BVT350LE | IC MPU PPC 350MHZ 255-FCPBGA |
| FMM44DSEN-S243 | CONN EDGECARD 88POS .156 EYELET |
| MC68302CRC16C | IC MPU NETWORK 16MHZ 132-PQA |
| MPC8533EVTARJA | MPU POWERQUICC 783-PBGA |
| FMM44DSEH-S243 | CONN EDGECARD 88POS .156 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC745CPX350LE | 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 350MHZ 255-FCPBGA |
| MPC745CVT350LE | 功能描述:微處理器 - MPU GF REV2.8@6W RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC75 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Metal Plate Cement Resistors |
| MPC750 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC750 RISC Microprocessor |
| MPC75-103J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Metal Plate Cement Resistors |
發布緊急采購，3分鐘左右您將得到回復。