參數資料
型號： MPC852T
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Hardware Specifications
中文描述： 硬件規格
文件頁數： 11/80頁
文件大?。?/td> 3080K
代理商： MPC852T
MPC852T Hardware Specifications, Rev. 3.1
Freescale Semiconductor
11
Mandatory Reset Configurations
One consequence of multiple power supplies is that when power is initially applied, the voltage rails ramp up at
different rates. The rates depend on the nature of the power supply, the type of load on each power supply, and the
manner in which different voltages are derived. The following restrictions apply:
V
DDL
must not exceed V
DDH
during power-on reset or power down.
V
DDL
must not exceed 1.9 V, and V
DDH
must not exceed 3.465.
These cautions are necessary for the long-term reliability of the part. If they are violated, the electrostatic discharge
(ESD) protection diodes are forward-biased, and excessive current can flow through these diodes. If the system
power supply design does not control the voltage sequencing, the circuit shown in
Figure 2
can be added to meet
these requirements. The MUR420 Schottky diodes control the maximum potential difference between the external
bus and core power supplies on power-on reset, and the 1N5820 diodes regulate the maximum potential difference
on power-down.
Figure 2. Example Voltage Sequencing Circuit
10 Mandatory Reset Configurations
The MPC852T requires a mandatory configuration during reset.
If hardware reset configuration word (HRCW) is enabled, by asserting the RSTCONF during HRESET assertion,
the HRCW[DBGC] value that is needed to be set to binary X1 in the hardware reset configuration word (HRCW)
and the SIUMCR[DBGC] should be programmed with the same value in the boot code after reset.
If hardware reset configuration word (HRCW) is disabled, by negating the RSTCONF during the HRESET
assertion, the SIUMCR[DBGC] should be programmed with binary X1 in the boot code after reset.
V
DDH
V
DDL
1N5820
MUR420
相關PDF資料
PDF描述
MPC852TVR100 Hardware Specifications
MPC852TVR50 Hardware Specifications
MPC852TVR66 Hardware Specifications
MPC852TVR80 Hardware Specifications
MPC859 Hardware Specifications
相關代理商/技術參數
參數描述
MPC852TADS 功能描述:開發板和工具包 - 其他處理器 ADS BOARD FOR 852 RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
MPC852TADS-KIT 功能描述:開發板和工具包 - 其他處理器 852TADS KIT RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
MPC852TCVR100A 功能描述:微處理器 - MPU Ethernet 100 MHz RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC852TCVR50A 功能描述:微處理器 - MPU Ethernet 50 MHz RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC852TCVR50A 制造商:Freescale Semiconductor 功能描述:Embedded Networking Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*