參數資料
型號： MSM82C37B-5RS
廠商： OKI SEMICONDUCTOR CO., LTD.
英文描述： Programmable DMA Controller(可編程DMA控制器)
中文描述： 可編程DMA控制器（可編程DMA的控制器）
文件頁數： 13/33頁
文件大?。?/td> 209K
代理商： MSM82C37B-5RS
13/33
Semiconductor
MSM82C37B-5RS/GS/VJS
Symbol
EOP
Pin Name
End of Process
Input/Output
Input/Output
Function
EOP
is active-low bidirectional three-state signal. Unlike other
pins, this pin is an N-channel open drain. During DMA operations,
a low-level output pulse is obtained from this pin if the channel
word count changes from 0000H to FFFFH.
And DMA transfers can be terminated by pulling the
EOP
input to
low level. Both of these actions are called terminal count (TC).
When internal or external
EOP
is generated, the MSM82C37B-5
terminates the transfer and resets the DMA request.
When the EOP pin is not used, it is necessary to hold the pin at
high level by pull-up resistor to prevent the input of an EOP
by error. Also note that the
EOP
function cannot be satisfied in
cascade mode.
Hold Request
HRQ
Output
HRQ is active-high signal used as an output of hold request to
the CPU for system data bus control purposes. After HRQ has
become active, at least one clock cycle is required before HLDA
becomes active.
Address Enable
AEN
Output
AEN is active-high ouput signal used to indicate that output
signals sent from the MSM82C37B-5 to the system are valid.
And in addition to enabling external latch to hold the eight higher
order bits of the transfer address, this signal is also used to
disable other system bus buffers.
ADSTB is active-high signal used to strobe the eight higher order
bits of the transfer address by external latch.
DMA Acknowledge
0 - 3 Channels
DACK
0
-
DACK
3
Output
DACK is output signals used to indicate that DMA transfer to
peripheral devices has been permitted. (Available in each channel.)
Although these pins are switched to active-low when reset, they
can be programmed to become active-high.
Note that there is no DACK output signal during memory-memory
transfers.
Address 0 - 3
A
0
- A
3
Input/Output
A
0
- A
3
is bidirectional three-state signals used as input signals
for specifying the MSM82C37B-5 internal register to be accessed
by the CPU during idle cycles, and as an output the four lower
order bits of the transfer address during active cycles.
A
4
- A
7
is three-state signals used as an output the four higher
order bits of the transfer address during active cycles.
Address 4 - 7
A
4
- A
7
Output
Memory Read
MEMR
Output
MEMR
is active-low three-state output signal used as a control
signal in reading data from memory during read transfers and
memory-memory transfers.
MEMW
is active-low three-state output signal used as a control
signal in writing data into memory during write transfers and
memory-memory transfers.
Memory Write
MEMW
Output
Address Strobe
ADSTB
Output
相關PDF資料
PDF描述
MSM82C37B-5VJS Programmable DMA Controller(可編程DMA控制器)
MSM82C51A-2(中文) Universal Synchronous Asynchronous Receiver Transmitter(通用同步/異步接收發送器,同步通訊最高可達64Kbps,異步通訊最高可達38.4Kbps)
MSM82C51A-2 Universal Synchronous Asynchronous Receiver Transmitter(通用同步/異步接收發送器,同步通訊最高可達64Kbps,異步通訊最高可達38.4Kbps)
MSM82C53-2 Programmable Universal Timers(可編程中斷定時器,最高計數頻率8MHz)
MSM82C54-2 Programmable Universal Timers(可編程中斷定時器,最高計數頻率10MHz)
相關代理商/技術參數
參數描述
MSM82C37B-5VJS 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:PROGRAMMABLE DMA CONTROLLER
MSM82C43 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:INPUT/OUTPUT PORT EXPANDER
MSM82C51A-2GS 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER
MSM82C51A-2GS-K 制造商:OK International 功能描述:USART, 32 Pin, Plastic, SOP 制造商:OKI Semiconductor 功能描述:USART, 32 Pin, Plastic, SOP
MSM82C51A-2JS 制造商:ROHM Semiconductor 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*