- 您現在的位置：買賣IC網 > PDF目錄68017 > MSM9000B-XXAV-Z-XX (OKI ELECTRIC INDUSTRY CO LTD) 16 X 60 DOTS DOT MAT LCD DSPL CTLR, UUC PDF資料下載
參數資料
| 型號： | MSM9000B-XXAV-Z-XX |
| 廠商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分類： | 顯示控制器 |
| 英文描述： | 16 X 60 DOTS DOT MAT LCD DSPL CTLR, UUC |
| 封裝： | 35 MM, TCP |
| 文件頁數： | 13/39頁 |
| 文件大?。?/td> | 389K |
| 代理商： | MSM9000B-XXAV-Z-XX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Semiconductor
20/39
MSM9000B-xx
FEDL9000B-01
CONT U/D (Contrast Up Down)
[1, 0, 0, X, 0, 0, 1, 1/0]
This command selects the voltage of VSS2, 3 that is used as the reference voltage for the LCD
bias. When the value of VSS2, 3 is changed, the contrast is changed accordingly.
The contrast is controlled by the value of the 3-bit up/down counter so that eight stages are
supported. The value of the up/down counter is incremented when "1" is entered by this
command and decremented when "0" is entered. The counter changes within the range of 0
to 7.
When the counter reaches 7, it goes back to "0".
According to the settings of N1 and N2, the contrast stages can be changed to 1 to 8, 2 to 9, or
3 to A.
At stage 0, the bias voltage is minimized. The larger the contrast stage, the higher the bias
voltage. At stage A, the bias voltage is maximized.
After a low RESET is input, the counter is set to the minimum value specified by N1 and N2.
Example: 67012345670
Note: At some contrast stages, the bias voltage may be increased to 5.5 V or higher. Adjust
the stage so that the bias voltage does not exceed 5.5 V.
STOP (Set Stop Mode)
[1, 0, 0, X, 0, 1, 0, 0]
This command sets standby mode. Specifically, the command stops the oscillation block to
prevent current form flowing through the oscillation block and outputs the VDD level to all
LCD output pins. Standby mode is canceled when D0 is set to "1" regardless of the setting of
the C/D pin. When a command or data with D0 set to "1" is entered, the command is executed
or the data is input. At the same time, standby mode is canceled.
After RESET = "L", standby mode is disabled.
SOE/D (Serial Out Enable/Disable)
[1, 0, 0, X, 0, 1, 1, 1/0]
This command controls the impedance of the SO output pin. The command is valid only when
the serial interface is used. When D0 is set to "0", the SO pin is set in the high impedance state.
After RESET = "L", D0 is set to "0".
DISP (Display On/Off)
[1, 0, 0, 1/0, 1, 0, 0, 1/0]
This command sets LCD display mode. When D0 is set to "1", the LCD is turned on. When
D0 is set to "0", the LCD is turned off, in which case, the VDD level is output to all segment and
common pins. When the LCD is turned ON (D0="1"), and D4 is set to "1", only arbitrators are
displayed and when D4 is set to "0", both characters and arbitrators are displayed. The table
below lists display modes.
After RESET = "L", both D4 and D0 are set to "0".
D4
D0
Characters
Arbitrators
X0
01
11
OFF
ON
OFF
ON
相關PDF資料 |
PDF描述 |
|---|---|
| MSM9000B-01AV-Z-XX | 16 X 60 DOTS DOT MAT LCD DSPL CTLR, UUC |
| MSM9202-01GS-BK | 16 X 35 DOTS FLUORESCENT DSPL CTRL, PQFP64 |
| MSM9202-01GS-K | 16 X 35 DOTS FLUORESCENT DSPL CTRL, PDSO64 |
| MSP430A006IRTDT | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430A007IRTDT | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM9004 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/3, 1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 49-DOT SEGMENT DRIVER |
| MSM9004-01 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/3, 1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 49-DOT SEGMENT DRIVER |
| MSM9004-02 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/3, 1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 49-DOT SEGMENT DRIVER |
| MSM9004-02GS-BK | 制造商:ROHM Semiconductor 功能描述: |
| MSM9004-03 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 50-DOT SEGMENT DRIVER |
發布緊急采購，3分鐘左右您將得到回復。