- 您現在的位置：買賣IC網 > PDF目錄68017 > MSM9000B-XXAV-Z-XX (OKI ELECTRIC INDUSTRY CO LTD) 16 X 60 DOTS DOT MAT LCD DSPL CTLR, UUC PDF資料下載
參數資料
| 型號： | MSM9000B-XXAV-Z-XX |
| 廠商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分類： | 顯示控制器 |
| 英文描述： | 16 X 60 DOTS DOT MAT LCD DSPL CTLR, UUC |
| 封裝： | 35 MM, TCP |
| 文件頁數： | 16/39頁 |
| 文件大?。?/td> | 389K |
| 代理商： | MSM9000B-XXAV-Z-XX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Semiconductor
23/39
MSM9000B-xx
FEDL9000B-01
Mode Setting after a Reset Input
The table below lists the settings of individual modes during a RESET =L input.
Even when a reset is input, display RAM is not initialized. To clear the display data, a blank
code must be written. (This can be done with an additional function of the AINC command.)
Mode Settings during Standby
The table below lists the settings of individual modes during standby.
Data before standby mode is retained in display RAM.
Command
Mode setting
Remarks
LPA
LOT
SF
The address pointer is set to "00".
Load Option command with no additional function.
The dividing ratio is set to 1.
A5 to A0 = "0"
I1 = "0", I0 = "0"
F1= "0", F0 = "0"
BKCG 1/0
Display addresses 00 to 11 are set.
D0 = "0"
CONT U/D
—
The control counter is set to 0 (Stage 0).
STOP
—
Standby mode is disabled.
SOE/D
The SO pin is set to the high impedance state.
D0 = "0"
DISP
Both characters and arbitrators display mode is set, but the dispaly is
turned off.
D4 = "0", D0 = "0"
ABB
Display data input mode is enabled.
D0 = "0"
BPC
Blink mode is such that the turning on of all dots and character display
are repeated.
D0 = "0"
ABLC
Arbitrator 1 corresponds to COM1, and arbitrator 2 corresponds to
COM2.
L1 = "0", L0 = "0"
Command
Mode setting
Remarks
LPA
LOT
SF
The address pointer is set to "00".
The setting before standby mode is retained.
A5 to A0 = "0"
No change
BKCG 1/0
CONT U/D
—
The count before standby mode is retained.
STOP
—
Standby state 10. No change.
SOE/D
The setting before standby mode is retained.
D0 = "0"
DISP
Both character and arbitrator display mode is set, but the display is
turned off.
D4 = "0", D0 = "0"
ABB
BPC
The setting before standby mode is retained.
No change
ABLC
相關PDF資料 |
PDF描述 |
|---|---|
| MSM9000B-01AV-Z-XX | 16 X 60 DOTS DOT MAT LCD DSPL CTLR, UUC |
| MSM9202-01GS-BK | 16 X 35 DOTS FLUORESCENT DSPL CTRL, PQFP64 |
| MSM9202-01GS-K | 16 X 35 DOTS FLUORESCENT DSPL CTRL, PDSO64 |
| MSP430A006IRTDT | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
| MSP430A007IRTDT | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM9004 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/3, 1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 49-DOT SEGMENT DRIVER |
| MSM9004-01 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/3, 1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 49-DOT SEGMENT DRIVER |
| MSM9004-02 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/3, 1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 49-DOT SEGMENT DRIVER |
| MSM9004-02GS-BK | 制造商:ROHM Semiconductor 功能描述: |
| MSM9004-03 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:1/4 DUTY LCD DRIVER WITH 4-DOT COMMON DRIVER AND 50-DOT SEGMENT DRIVER |
發布緊急采購，3分鐘左右您將得到回復。