參數資料
型號： MULTILYNX
英文描述： MultiLynx CL2151 Universal HFC? Interactive Cable Transceiver
中文描述： MultiLynx CL2151通用光纖？交互式有線電視收發器
文件頁數： 52/52頁
文件大?。?/td> 517K
代理商： MULTILYNX
52
MON08 Multilink User Manual
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
PROG08SZ software continually records any changes to these security bytes
and stores them in the file SECURITY.INI. The information in this file is also
shared with P&E's In-Circuit Debugger and In-Circuit Simulator Software.
This allows the user to reset the device and still have access to the monitor
mode.
Sometimes the case comes up where the software can’t pass security mode.
The Target Connection and Security Dialog section has a “STATUS” section
which describes the different failures and what to check in each case.
The most common reasons for not passing security are:
- You are not choosing the proper security code to pass security.
- On a power on reset, the device is not powering down to below 0.1
volts. With a Class I board (ICS with processor), you may be driving
the pins on the emulation header while the device is being powered
down. This back-drives current through the ports and doesn’t let the
device fully power down. On other classes of boards, when prompted
to power down the device, the supply voltage might not be dropping
lower than 0.1v which it must to have a power-on reset.
- Make sure the “Target hardware type” is set to the proper class of
hardware.
There are several ways you can specify the proper security bytes:
- If you know the programmed security bytes, i.e. the bytes from
$FFF6-$FFFD, you can enter them in the edit box listed “User:” and
click OK(Retry).
- You can use the “Load from S19” to specify the s-record file which
contains the object information currently programmed into the MCU.
P&E’s software will automatically extract the security information
from this file and use it to pass security. Once you have specified the
s-record file, click the OK(Retry) button.
- You can erase the device. Run the PROG08SZ application, and when the
above box appears, select the “IGNORE security failure…” option and click
OK. Use the Choose Module command to select the appropriate programming
algorithm, and select Erase Module. This should erase the device. You will
have to execute the Choose Module command again before you can access the
blank device. Note: on some older revisions of silicon, you can’t ignore the
security failure, and it will bring this box back up every time you click
OK(Retry). If this is the case, you should obtain the latest silicon revision from
Motorola.
相關PDF資料
PDF描述
MULTISYNCFE750 Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A
MUM8128W-17 x8 EPROM
MUM8128W-20 x8 EPROM
MUM8128W-25 x8 EPROM
MUM8128WI-17 x8 EPROM
相關代理商/技術參數
參數描述
MULTIMAX-8G+ 功能描述:程序設計器 - 基于通用和內存 HI PERF STAND ALONE PRGRAMER FOR 8-SOCK RoHS:否 制造商:Xeltek 產品:Universal Device Programmers 工具用于評估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口類型:Parallel, USB 工作電源電壓:90 VAC to 250 VAC
MULTIPHSPOL-RD 功能描述:電源管理IC開發工具 Si825x Multi-Phase POL Reference Design RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
MULTI-PRO 制造商:ERSA 功能描述:SOLDERING IRON 230V 20W EURO PLUG 制造商:ERSA 功能描述:SOLDERING IRON, 230V, 20W, EURO PLUG
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*