參數資料
型號: MVTX2804
廠商: Zarlink Semiconductor Inc.
英文描述: 8-Port 1000 Mbps Ethernet Distributed Switch
中文描述: 8端口1000 Mbps以太網交換機分布式
文件頁數: 37/174頁
文件大?。?/td> 2249K
代理商: MVTX2804
MVTX2804
Data Sheet
37
Zarlink Semiconductor Inc.
Figure 7 - Timing diagram for serial mode in LED interface
The status bits shown in here are flow control (FC), transmitting data (TxD), receiving data (RxD), link up (LNK),
speed (SP0 and SP1), full duplex (FDX), and collision (COL). Note that SP[1:0] is defined as 10 for 1 Gbps, 01
for 100 Mbps, and 00 for 10 Mbps.
Also note that U0-U7 represent user-defined sub-frames in which additional status information may be
embedded. We will see later that the MVTX2804 provides registers that can be written by the CPU to indicate
this additional status information as it becomes available.
9.3 Parallel Mode
In parallel mode, the following pins are utilized:
LED_PORT_SEL[9:0] - indicates which of the 8 Gigabit port status bytes or 2 user-defined status bytes is
being read out
LED_BYTEOUT_[7:0] - provides 8 bits for 8 different port status indicators. Note that these bits are active
low.
By default, the system is in parallel mode. In parallel mode, the 10 status bytes are scanned in a continuous
loop, with one byte read out per clock cycle, and the appropriate port select bit asserted.
9.4 LED Control Registers
An LED Control Register can be used for programming the LED clock rate, sample hold time, and pattern in
parallel mode.
In addition, the MVTX2804 provides 8 registers called LEDUSER[7:0] for user-defined status bytes. During
operation, the CPU can write values to these registers, which will be read out to the LED interface output (serial
or parallel). Only LEDUSER[1:0] are used in parallel mode. The content of the LEDUSER registers will be sent
out by the LED serial shift logic, or in parallel mode, a byte at a time.
Because in parallel mode there are only two user-defined registers, LEDUSER[7:2] is shared with LEDSIG[7:2].
For LEDSIG[j], where j = 2, 3, …, 6, the corresponding register is used for programming the LED pin
LED_BYTEOUT_[j]. The format is as follows:
Bits [3:0]Signal polarity:
0: do not invert polarity (high true)
1: invert polarity
7
4
3
0
COL
FDX
SP1
SP0
COL
FDX
SP1
SP0
P0
info
P1
info
P2
info
P3
info
P4
info
P5
info
P6
info
P7
info
U0
U1
U2
U3
U4
U5
U6
U7
LE_SYNCO
LE_DO
LE_CLKO
FC
TxD
RxD
LNK
SP0
SP1
FDX
COL
0
7
6
5
4
3
2
1
相關PDF資料
PDF描述
MVTX2804AG 8-Port 1000 Mbps Ethernet Distributed Switch
MVV200 Analog IC
MW005A DC-to-DC Voltage Converter
MW005AJ DC-to-DC Voltage Converter
MW005AJ4 DC-to-DC Voltage Converter
相關代理商/技術參數
參數描述
MVTX2804AG 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:8-Port 1000 Mbps Ethernet Distributed Switch
MVTX2804AG2 制造商:Microsemi Corporation 功能描述:
MVU10-10FBK 功能描述:端子 D-10-1103K BS-33-10-P 85299 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
MVU10-10FBX 功能描述:端子 BLOCK FORK VNYL INS BTL BS-33-10-P RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
MVU10-10FBX-BOTTLE 功能描述:CONN FORK BLOCK INSUL 50PC RoHS:是 類別:連接器,互連式 >> 端子 - 鏟形 系列:Scotchlok™ 標準包裝:1 系列:Scotchlok™ 端子類型:彈簧,壓接式 接線柱/接片尺寸:10 接線柱 寬度 - 外邊:0.320"(8.13mm) 長度 - 總體:1.030"(26.16mm) 安裝類型:自由懸掛 端子:壓接 線規:10-12 AWG 絕緣體:絕緣 特點:- 顏色:黃 包裝:散裝 觸點表面涂層:錫 觸點材料:銅,ETP 絕緣體直徑:0.250"(6.35mm) 材料 - 絕緣體:聚酰胺(PA),尼龍 長度 - 環心道末端:0.280"(7.11mm) 長度 - 末端:0.550"(13.97mm) 內部舌簧打開:- 相關產品:TR-490-ND - HAND CRIMP TOOL RACHET 10-22 AWGTH-450-ND - TOOL HAND CRIMP 6-26AWGTR-482-ND - TOOL RATCHETING 10-22AWG CRIMP920099-R-ND - TOOL 10-22AWG SCOTCHLOK CRIMP 其它名稱:000511285879115112858791180611464373