參數資料
型號： OX16PCI954-TQC60-A
廠商： Electronic Theatre Controls, Inc.
英文描述： Integrated Quad UART and PCI interface
中文描述： 綜合四UART和PCI接口
文件頁數： 25/72頁
文件大?。?/td> 656K
代理商： OX16PCI954-TQC60-A
Data Sheet Revision 1.3
Page 25
OX16PCI954
OXFORD SEMICONDUCTOR LTD.
6.4.8
Bits
3:0
Global Interrupt Status and Control Register ‘GIS’ (Offset 0x1C)
Description
These bits reflect the state of UART3 to UART0 internal interrupt lines,
respectively.
1
MIO0 (Mode[1:0]
≠
‘01’). This bit reflects the state of the internal MIO[0]. The
internal MIO[0] reflects the non-inverted or inverted state of MIO0 pin.
2
Parallel Port Interrupt (Mode[1:0]=‘01’). This bit reflects the state of the Parallel
Port internal interrupt line.
MIO1 (LCC[6:5]=‘00’). This bit reflects the state of the internal MIO[1]. The
internal MIO[1] reflects the non-inverted or inverted state of MIO1 pin.
2
Function0 Power-down Interrupt (LCC[6:5]
≠
‘00’). In this mode this is a sticky
bit. When set, it indicates a power-down request issued by Function0 and
would normally have asserted a PCI interrupt if bit 21 was set (see section
7.9). Reading this bit clears it.
These bits reflect the state of the internal MIO[11:2]. The internal MIO[11:2]
reflect the non-inverted or inverted state of MIO[11:2] pins respectively.
2
UART Interrupt Mask. When set (=1) these bit enable each internal UART to
assert a PCI interrupt respectively. When cleared (=0) they prevent the
respective channel fromasserting a PCI interrupt.
3
MIO[0] Interrupt Mask (Mode[1:0]
≠
‘01’). When set (=1) this bit enables MIO0
pin to assert a PCI interrupt. When cleared (=0) it prevents MIO0 pin from
asserting a PCI interrupt.
2
Parallel Port Interrupt Mask (Mode[1:0]=‘01’). When set (=1) this bit enables
the Parallel Port to assert a PCI interrupt. When cleared (=0) it prevents the
Parallel Port fromasserting a PCI interrupt.
MIO[1] Interrupt Mask (LCC[6:5]=‘00’). When set (=1) this bit enables MIO1 pin
to assert a PCI interrupt. When cleared (=0) it prevents MIO1 pin from
asserting a PCI interrupt.
2
Function0 Power-down Interrupt Mask (LCC[6:5]
≠
‘00’). When set (=1) this bit
enables the power-down logic in Function0 to assert a PCI interrupt. When
cleared (=0) it prevents the power-down logic in Function0 fromasserting a
PCI interrupt.
MIO Interrupt Mask. When set (=1) these bits enable each MIO[11:2] pin to
assert a PCI interrupt respectively. When cleared (=0) they prevent the
respective pins fromasserting a PCI interrupt.
2
Read/Write
EEPROM
-
Reset
0x0h
PCI
R
4
-
-
R
R
R
X
0
X
0
5
15:6
-
R
XXXh
19:16
W
RW
Fh
20
W
W
RW
RW
1
1
21
W
W
RW
RW
1
0
31:22
W
RW
3FFh
Note 1:
GIS[3:0] are the inverse of UIS[24], UIS[18], UIS[6] and UIS[0] respectively. Systems that do not require the Local Bus or parallel port need not read
this register to identify the source of the interrupt as long as they read the UIS (offset 18h) register.
Note 2:
The returned value is either the direct state of the corresponding MIO pin or its inverse as configured by the Multi-purpose I/O Configuration register
‘MIC’ (offset 0x04). As the internal MIO can assert a PCI interrupt, the inversion feature can define each external interrupt to be defined as active-low
or active-high, as controlled by the MIC register.
Note 3:
The UART Interrupt Mask register bits are all set after a hardware reset to enable the interrupt fromall internal UARTs. This will cater for generic
device-driver software that does not access the Local Configuration Registers. The default setting for UART Interrupt Mask bits can be changed
using the serial EEPROM. Note that even though by default the UART interrupts are enabled in this register, since after a reset the IER registers of
individual UARTs disables all interrupts, a PCI interrupt will not be asserted after a hardware reset.
Note 4:
When Mode[1:0]=‘10’, the MIO pins are used to define a SubsystemID value, therefore all interrupts due to MIO pins are disabled regardless of the
state of the GIS register. The MIO Interrupts Mask register bits are all set after a hardware reset to enable the interrupt fromall MIO pins fromboot
up. The default setting for MIO Interrupt Mask bits can be changed using the serial EEPROM.
相關PDF資料
PDF描述
OX4240 OCXO
OX1040 OCXO
OX1041 OCXO
OX1042 OCXO
OX1140 OCXO
相關代理商/技術參數
參數描述
OX16PCI954-TQC60-A1 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated Quad UART and PCI interface
OX16PCI958 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Octal UART with PCI Interface
OX16PCI958-PQAG 功能描述:外圍驅動器與原件 - PCI Universal PCI bridge to octal serial port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
OX-1700-BAE-107 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Oven Controlled Crystal Oscillator
OX-1700-BAE-108 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Oven Controlled Crystal Oscillator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*