- 您現在的位置：買賣IC網 > PDF目錄383727 > OX16PCI954-TQC60-A (Electronic Theatre Controls, Inc.) Integrated Quad UART and PCI interface PDF資料下載
參數資料
| 型號： | OX16PCI954-TQC60-A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Integrated Quad UART and PCI interface |
| 中文描述： | 綜合四UART和PCI接口 |
| 文件頁數： | 26/72頁 |
| 文件大?。?/td> | 656K |
| 代理商： | OX16PCI954-TQC60-A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
6.5
Data Sheet Revision 1.3
Page 26
OX16PCI954
OXFORD SEMICONDUCTOR LTD.
PCI Interrupts
Interrupts in PCI systems are level-sensitive and can be
shared. There are sixteen sources of interrupt in the
OX16PCI954, one in each UART channel and twelve from
Multi-Purpose IO pins (MIO11 to MIO0). The Parallel Port
and MIO0 share the same interrupt status bit (GIS[4]). The
PCI Power Management power-down interrupt for internal
UARTs (Function0) and MIO1 share the status bit GIS[5].
The Local Bus uses the MIO pins to pass interrupts to the
PCI controller.
All interrupts are routed to the PCI interrupt pins, INTA#or
INTB# The default routing asserts Function0 interrupts on
INTA#and Function1 interrupts on INTB# These default
routings may be modified by writing to the Interrupt Pin field
in the configuration registers using the serial EEPROM
facility. The Interrupt Pin field is normally considered a
hard-wired read-only value in PCI. It indicates to system
software which PCI interrupt pin (if any) is used by a
function. The interrupt pin may only be modified using the
serial EEPROMfacility, and card developers must not
invoke any combination which violates the PCI
specification. Note that OX16PCI954 only has two PCI
interrupt pins, INTA#and INTB#. If in doubt, the default
routings should be used. Table 10 relates the Interrupt Pin
field to the device pin used.
Interrupt Pin
Device Pin used
0
1
2
3 to 255
None
INTA#
INTB#
Reserved
Table 10: ‘Interrupt pin’ definition
During the systeminitialisation process and PCI device
configuration, system-specific software reads the interrupt
pin field to determne which (if any) interrupt pin is used by
each function. It programmes the systeminterrupt router to
logically connect this PCI interrupt pin to a system-specific
interrupt vector (IRQ). It then writes this routing information
to the Interrupt Line field in the functions PCI configuration
space. Device driver software must then hook the interrupt
using the information in the Interrupt Line field.
Interrupt status for all sixteen sources of interrupt is
available using the GIS register in the Local Configuration
Register set, which can be accessed using I/O or Memory
accessed fromboth logical functions. This facility enables
each function to snoop on interrupts asserted fromthe
other function regardless of the interrupt routing.
The interrupt fromeach UART channel is enabled using
the IER register and the MCR register for that UART. If the
interrupt is enabled and active, then the device will drive
the PCI interrupt pin low. Generic device driver software
will use the IER register to enable interrupts. The
OX16PCI954 offers additional interrupt masking ability
using GIS[19:16] (see section 6.4.8). An internal UART
channel may assert a PCI interrupt if the interrupt is
enabled by IER and GIS[19:16].
All interrupts can be enabled / disabled individually using
the GIS register set in the Local configuration registers.
When an MIO pin is enabled, an external device can assert
a PCI interrupt by driving that pin. The sense of the MIO
external interrupt pins (active-high or active-low) is defined
in the MIC register. The parallel port can also assert an
interrupt (Note: this effectively disables the MIO[0]
interrupt).
相關PDF資料 |
PDF描述 |
|---|---|
| OX4240 | OCXO |
| OX1040 | OCXO |
| OX1041 | OCXO |
| OX1042 | OCXO |
| OX1140 | OCXO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OX16PCI954-TQC60-A1 | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated Quad UART and PCI interface |
| OX16PCI958 | 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Octal UART with PCI Interface |
| OX16PCI958-PQAG | 功能描述:外圍驅動器與原件 - PCI Universal PCI bridge to octal serial port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| OX-1700-BAE-107 | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Oven Controlled Crystal Oscillator |
| OX-1700-BAE-108 | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Oven Controlled Crystal Oscillator |
發布緊急采購，3分鐘左右您將得到回復。