參數資料
型號: OX16PCI954
廠商: Electronic Theatre Controls, Inc.
英文描述: Integrated Quad UART and PCI interface
中文描述: 綜合四UART和PCI接口
文件頁數: 52/72頁
文件大小: 656K
代理商: OX16PCI954
8.3
Data Sheet Revision 1.3
Page 52
OX16PCI954
OXFORD SEMICONDUCTOR LTD.
Configuration & Programming
The configuration registers for the local bus controller are
described in sections 6.4.3 & 6.4.4. The values of these
registers after reset allow the host systemto identify the
function and configure its base address registers.
Alternatively many of the default values can be re-
programmed during device initialisation through use of the
optional serial EEPROM(see section 10).
The I/O space block can be varied in size from4 bytes to
256 bytes (32 bytes is the default) by setting LT2[22:20]
accordingly. Varying the block size means that I/O space
can be allocated efficiently by the system whatever the
application.
The I/O block can then be divided into one, two or four
chip-select regions, depending on the setting in LT2[26:23].
To divide the area into four chip-select region, the user
should select the second uppermost non-zero address bit
as the Lower-Address-CS-decode. To divide into two
regions, the user should select the uppermost address bit.
If an address bit beyond the selected range is selected, the
entire I/O space is allocated to CS0# For example, if 32
bytes of I/O space are reserved, the active address lines
are A[4:0]. To divide this into four regions, the Lower
Address CS parameter should be set to A3, by
programmng the value ‘0001’ into LT2[26:23]. To select
two regions, choose A4, and to maintain one region, select
any value greater than A4.
In 8-bit mode, the memory space block is always 4K bytes,
and always divided into four chip-select regions of 1K byte
each.
In 32-bit mode, again the I/O space can be varied in size
from4 bytes to 256 bytes. It is also possible to increase the
memory space block size from4K bytes to 16K bytes. Also
in 32-bit mode, the Lower-Address-CS-Decode parameter
afftects division of the I/O space AND memory space into
chip-select regions.
A soft reset facility is provided so software can
independently reset the peripherals on the local bus. The
local bus reset signals, LBRST and LBRST# are always
active during a PCI bus reset and also when the
configuration register bit LT2[29] is set to 1.
The clock enable bit, when set, enables a copy of the PCI
bus clock output on the local bus pin LBCLK. A buffered
UART clock can also be asserted on the UART_Clk_Out
pin; this means that a single oscillator can be used to drive
serial ports on the local bus as well as the internal UARTs.
相關PDF資料
PDF描述
OX16PCI954-TQC60-A Integrated Quad UART and PCI interface
OX4240 OCXO
OX1040 OCXO
OX1041 OCXO
OX1042 OCXO
相關代理商/技術參數
參數描述
OX16PCI954_05 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated Quad UART and PCI interface
OX16PCI954-TQA1G 功能描述:外圍驅動器與原件 - PCI PCI bridge to quad serial & para. port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
OX16PCI954-TQC60-A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Integrated Quad UART and PCI interface
OX16PCI954-TQC60-A1 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Integrated Quad UART and PCI interface
OX16PCI958 制造商:OXFORD 制造商全稱:OXFORD 功能描述:Octal UART with PCI Interface