參數資料
型號： P1803ACRP
英文描述： SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
中文描述： SIDAC的|高達210V五（公報）最大| 800mA的我（縣）|對220VAR
文件頁數： 133/161頁
文件大小： 986K
代理商： P1803ACRP
SIDACtor
Data Book
Soldering Recommendations
Teccor Electronics
(972) 580-7777
5 - 17
T
excess of 215
°
C, care should be taken such that the maximum temperature of the
leads does not exceed 275
°
C and the maximum temperature of the plastic body does
not exceed 250
°
C (Figure 5-8).
Figure 5-7 Principle of Vapor Phase Soldering
Figure 5-8 Reflow Soldering Profile
During reflow, the surface tension of the liquid solder will draw the leads of the device
towards the center of the soldering area, correcting any misalignment that may have
occurred during placement and allowing the device to set flush on the pad. However, if
the footprints of the pad are not concentrically aligned, the same effect can result in
undesirable shifts as well, hence the importance of using a standard contact pattern
which leaves sufficient room for self-positioning.
After the solder has cooled, connections should be visually inspected and remnants of
the flux removed using a vapor degreaser with an azeotrope solvent or equivalent.
Transport
Cooling pipes
PC board
Heating
elements
Boiling liquid (primary medium)
Vapor phase
zone
Vapor lock
(secondary
medium)
Time (Seconds)
0
0
20
40
60
80
100
120
140
160
180
200
220
240
30
60
90
120
150
180
210
240
270
300
T
C
Pre-Heat
Soak
Reflow
Cool
Down
0.5 - 0.6
C/Sec
1.3 - 1.6
C/Sec
<2.5
C/Sec
<2.5
C/Sec
Peak Temp.
210 - 235
C
Soaking Zone
Reflow Zone
Pre-heating Zone
( 2.0 - 4.0 min. max. )
( 2.0 min. max. )
60 - 90 sec. typical
( 2.0 min. max. )
30 - 60 sec. typical
相關PDF資料
PDF描述
P2200AA61RP 16-pin, 1.75KB, Flash, 72B RAM, 2x Comparator, 8HMz internal osc,Hi Volt Support, -40C to +85C, 14-PDIP, TUBE
P2202AA 16 PIN, 1.75KB FLASH, 64B RAM, 6 I/O, 8MHZ INTERNAL OSCILLATOR, -40C to +125C, 16-QFN, T/R
P2202AARP 14 PIN, 4KB FLASH, 128 RAM, 12 I/O, -40C to +85C, 16-QFN, T/R
P2202AB 14 PIN, 4KB FLASH, 128 RAM, 12 I/O, -40C to +85C, 14-TSSOP, T/R
P2202ABRP SIDAC|130V V(BO) MAX|800MA I(S)|TO-220VAR
相關代理商/技術參數
參數描述
P1803U 制造商:TECCOR 制造商全稱:TECCOR 功能描述:solid state crowbar devices
P1803U_L 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Balanced Three-chip SIDACtor
P1803UALRP 功能描述:硅對稱二端開關元件 3Chp 150V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803UALTP 功能描述:硅對稱二端開關元件 3Chp 150V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803UALXX 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:The series provides a single port surface mount solution that enables voice
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*