參數資料
型號： P1803ACRP
英文描述： SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
中文描述： SIDAC的|高達210V五（公報）最大| 800mA的我（縣）|對220VAR
文件頁數： 86/161頁
文件大?。?/td> 986K
代理商： P1803ACRP
ITU-T K.20 and K.21
SIDACtor
Data Book
4 - 12
Teccor Electronics
(972) 580-7777
External Protectors
For equipment being tested to the exposed level, it is standard practice for external
line protectors (typically gas tubes) to be used in order to handle the large surge
currents generated during K.20 and K.21 qualification. Realizing that these protectors
can affect the characteristics of the EUT, it is important that the protectors used be
agreed upon by the principal parties involved (the equipment supplier and testing
administrator). Once agreed upon, the protectors should be used when primary
protection is specified, and allowance should be given for a new set of protectors after
the completion of each test sequence.
Note:
An alternative to using external protectors is for the test administrator to simulate the
conditions expected (as if the external protectors were used) by modifying the surges
found in K.20 and K.21.
Equipment Boundaries
Because of the numerous types of equipment, during K.20 and K.21 testing ITU-T
looks at each EUT as a
“
black box
”
with three terminals (A, B, and E). The applicant is
expected to define the boundaries of this
“
black box
”
, and in doing so, should be aware
that any protective device within these boundaries is considered an unchangeable part
of that piece of equipment.
Permitted Malfunction or Damage
During K.20 and K.21 qualification, ITU-T recognizes two levels of malfunction or
damage to the EUT:
Level A states that equipment withstands the test without damage or disturbance
and operates properly after the test. If specifically permitted, the administration
may accept the opening of the fuse.
Level B states that a fire hazard does not occur in the equipment as a result of the
test, and that any permanent damage or malfunction is confined to a small number
of external line interface circuits (as defined by the test administrator).
The acceptable level of malfunction for each test is specified under Acceptance
Criteria.
相關PDF資料
PDF描述
P2200AA61RP 16-pin, 1.75KB, Flash, 72B RAM, 2x Comparator, 8HMz internal osc,Hi Volt Support, -40C to +85C, 14-PDIP, TUBE
P2202AA 16 PIN, 1.75KB FLASH, 64B RAM, 6 I/O, 8MHZ INTERNAL OSCILLATOR, -40C to +125C, 16-QFN, T/R
P2202AARP 14 PIN, 4KB FLASH, 128 RAM, 12 I/O, -40C to +85C, 16-QFN, T/R
P2202AB 14 PIN, 4KB FLASH, 128 RAM, 12 I/O, -40C to +85C, 14-TSSOP, T/R
P2202ABRP SIDAC|130V V(BO) MAX|800MA I(S)|TO-220VAR
相關代理商/技術參數
參數描述
P1803U 制造商:TECCOR 制造商全稱:TECCOR 功能描述:solid state crowbar devices
P1803U_L 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Balanced Three-chip SIDACtor
P1803UALRP 功能描述:硅對稱二端開關元件 3Chp 150V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803UALTP 功能描述:硅對稱二端開關元件 3Chp 150V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803UALXX 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:The series provides a single port surface mount solution that enables voice
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*