參數資料
型號： P2500AA61RP
英文描述： MCU CMOS 80 LD 33MHZ 8K EPRM, 0C to +70C, 80-TQFP, TRAY
中文描述： SIDAC的| 290V五（公報）最大| 800mA的我（縣）|對220VAR
文件頁數： 93/161頁
文件大?。?/td> 986K
代理商： P2500AA61RP
SIDACtor
Data Book
FCC PART 68
Teccor Electronics
(972) 580-7777
4 - 19
R
R
8%(4
Overview
FCC Part 68 applies to all terminal equipment that is connected to the public network
and is unique in the fact that it is mandated by U.S. law.
The purpose of FCC Part 68 is to provide a set of uniform standards that will protect
the telephone network from any damage or interference caused by the connection of
terminal equipment. The FCC standard includes environmental simulations such as
vibration tests, temperature and humidity cycling, drop tests and tests for hazardous
voltages and currents, as well as tests for signal power levels, line balance, on-hook
impedance, and billing protection; all of which must be met before and after the
environmental tests are applied.
Over-Voltage Test
FCC compliant equipment must undergo an over-voltage test that includes a Type A
and Type B Metallic Voltage Surge and a Type A and Type B Longitudinal Voltage
Surge. These surges are part of FCC's environmental simulation, and although there is
a provision which allows the EUT to reach an open circuit failure mode during the Type
A tests, failures must:
1. Arise from an intentional design which will cause the phone to be either
disconnected from the public network or repaired rapidly.
2. Be designed such that it is substantially apparent to the end user that the
terminal equipment is not operable. A common example of an acceptable
failure would be an open circuit due to an open connection on either Tip or
Ring.
For Type B surges, equipment protection circuitry is not allowed to fail. The EUT must
be designed to withstand Type B surges and continue to function in all operational
states.
Metallic Voltage Surge
The Type A and Type B Metallic Voltage Surges are applied in both the positive and
negative polarity across Tip and Ring during all operational states (on-hook, off-hook,
ringing, etc.). The Type A surge is an 800V, 100A peak surge while the Type B surge is
a 1000V, 25A peak surge (Table 4-16).
Longitudinal Voltage Surge
The Type A and Type B Longitudinal Voltage Surges are applied in both positive and
negative polarity during all operational states. The Type A surge is a 1500V, 200A
peak surge applied to the EUT with Tip and Ring tied together with respect to ground.
The Type B Longitudinal Voltage Surge is a simultaneous surge in which 1500V and
37.5A are applied to Tip with respect to ground and Ring with respect to ground
concurrently (Table 4-16).
相關PDF資料
PDF描述
P2600EA MCU CMOS 28 LD 40MHZ 8K OTP, -40C to +125C, 28-SPDIP, TUBE
P2600EARP1 MCU CMOS 28 LD 40MHZ 8K OTP, -40C to +85C, 28-SPDIP, TUBE
P2702AA MCU CMOS 84 LD LOW PWR, -40C to +85C, 84-PLCC, TUBE
P2702AARP SIDAC|160V V(BO) MAX|800MA I(S)|TO-220VAR
P2702AB SIDAC|160V V(BO) MAX|800MA I(S)|TO-220VAR
相關代理商/技術參數
參數描述
P2500ATL 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes
P2500B 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes
P2500BTL 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes
P2500D 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes
P2500DTL 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*