- 您現在的位置：買賣IC網 > PDF目錄3792 > P89LPC952FA,512 (NXP Semiconductors)IC 80C51 MCU FLASH 8K 44-PLCC PDF資料下載
參數資料
| 型號： | P89LPC952FA,512 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 17/69頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 80C51 MCU FLASH 8K 44-PLCC |
| 產品培訓模塊： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 標準包裝： | 26 |
| 系列： | LPC900 |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 40 |
| 程序存儲器容量： | 8KB（8K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 512 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 包裝： | 管件 |
| 產品目錄頁面： | 706 (CN2011-ZH PDF) |
| 配用： | 622-1016-ND - BOARD FOR P89LPC952FA 44-PLCC 622-1008-ND - BOARD FOR LPC9103 10-HVSON OM10075-ND - EVAL BOARD FOR LPC952 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART 568-3510-ND - DEMO BOARD SPI/I2C TO UART 622-1002-ND - USB IN-CIRCUIT PROG LPC9XX 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X |
| 其它名稱： | 568-2253-5 935280148512 P89LPC952FA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
P89LPC952_954_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 24 July 2008
24 of 69
NXP Semiconductors
P89LPC952/954
8-bit microcontroller with 10-bit ADC
in reset when VDD falls below the minimum specied operating voltage. These
requirements for clock frequencies above 12 MHz do not apply when using the
internal RC oscillator in clock doubler mode.
7.3.6 Clock output
The P89LPC952/954 supports a user-selectable clock output function on the
XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs if
another clock source has been selected (on-chip RC oscillator, watchdog oscillator,
external clock input on XTAL1) and if the RTC is not using the crystal oscillator as its clock
source. This allows external devices to synchronize to the P89LPC952/954. This output is
enabled by the ENCLK bit in the TRIM register.
The frequency of this clock output is 1
2 that of the CCLK. If the clock output is not needed
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
7.4 On-chip RC oscillator option
The P89LPC952/954 has a 6-bit TRIM register that can be used to tune the frequency of
the RC oscillator. During reset, the TRIM value is initialized to a factory pre-programmed
value to adjust the oscillator frequency to 7.373 MHz
± 1 % at room temperature.
End-user applications can write to the TRIM register to adjust the on-chip RC oscillator to
other frequencies. When the clock doubler option is enabled (UCFG1.3 = 1), the output
frequency is 14.746 MHz. If CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can
be set to logic 1 to reduce power consumption. On reset, CLKLP is logic 0 allowing
highest performance access. This bit can then be set in software if CCLK is running at
8 MHz or slower.
The requirements in Section 7.3.5 “High speed oscillator option” for conguring P1.5 as
an external reset input and using an external reset circuit when the clock frequency is
greater than 12 MHz do not apply when using the internal RC oscillator’s clock doubler
option.
7.5 Watchdog oscillator option
The watchdog has a separate oscillator which has a frequency of 400 kHz. This oscillator
can be used to save power when a high clock frequency is not needed.
7.6 External clock input option
In this conguration, the processor clock is derived from an external source driving the
P3.1/XTAL1 pin. The rate may be from 0 Hz up to 18 MHz. The P3.0/XTAL2 pin may be
used as a standard port pin or a clock output.
When using an external clock input frequency above 12 MHz, the reset input
function of P1.5 must be enabled. An external circuit is required to hold the device
in reset at power-up until VDD has reached its specied level. When system power is
removed VDD will fall below the minimum specied operating voltage. When using
an external clock input frequency above 12 MHz, in some applications, an external
brownout detect circuit may be required to hold the device in reset when VDD falls
below the minimum specied operating voltage. These requirements for clock
frequencies above 12 MHz do not apply when using the internal RC oscillator in
clock doubler mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 1301970347 | CONN SOCKET CONTACT 14AWG |
| MC9S08DN60VLF | MCU 8BIT 60K FLASH 48-LQFP |
| MC9S08DN48ACLH | MCU 8BIT 48K FLASH 64-LQFP |
| MC9S08AC48MFUE | MCU 8BIT 48K FLASH 64-QFP |
| MC9S08AC48MFJE | MCU 8BIT 48K FLASH 32-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC952FBD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC952FBD,157 | 功能描述:8位微控制器 -MCU 80C51 8K FL 512B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC954 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FA,529 | 功能描述:8位微控制器 -MCU 16K FL/1K RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。