- 您現在的位置：買賣IC網 > PDF目錄3776 > PCA9539PW,112 (NXP Semiconductors)IC I/O EXPANDER I2C 16B 24TSSOP PDF資料下載
參數資料
| 型號： | PCA9539PW,112 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 36/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 24TSSOP |
| 產品培訓模塊： | I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 63 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 16 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
| 包括： | POR |
| 產品目錄頁面： | 825 (CN2011-ZH PDF) |
| 其它名稱： | 568-5025 935277298112 PCA9539PW PCA9539PW,112-ND PCA9539PW-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁
PCA9539_PCA9539R
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 6 — 6 February 2013
8 of 37
NXP Semiconductors
PCA9539; PCA9539R
16-bit I2C-bus and SMBus low power I/O port with interrupt and reset
6.2.5 Registers 6 and 7: Configuration registers
This register configures the directions of the I/O pins. If a bit in this register is set (written
with ‘1’), the corresponding port pin is enabled as an input with high-impedance output
driver. If a bit in this register is cleared (written with ‘0’), the corresponding port pin is
enabled as an output. At reset, the device's ports are inputs.
6.3 Power-on reset
When power is applied to VDD, an internal power-on reset holds the PCA9539; PCA9539R
in a reset condition until VDD has reached VPOR. At that point, the reset condition is
released and the PCA9539; PCA9539R registers and SMBus state machine will initialize
to their default states. Thereafter, VDD must be lowered below 0.2 V to reset the device.
For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the
operating voltage.
6.4 RESET input
A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). In
the PCA9539 the registers and SMBus/I2C-bus state machine will be held in their default
state until the RESET input is once again HIGH. This input typically requires a pull-up to
VDD. In the PCA9539R, only the device state machine is initialized. The internal
general-purpose registers remain unchanged. Using the PCA9539R hardware reset pin
will only reset the I2C-bus interface should it be stuck LOW to regain access to the
I2C-bus. This allows the I/O pins to retain their last configured state so that they can keep
any lines in their previously defined state and not cause system errors while the I2C-bus is
being restored.
6.5 I/O port
When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a
high-impedance input. The input voltage may be raised above VDD to a maximum of 5.5 V.
If the I/O is configured as an output, then either Q1 or Q2 is on, depending on the state of
the Output port register. Care should be exercised if an external voltage is applied to an
I/O configured as an output because of the low-impedance path that exists between the
pin and either VDD or VSS.
Table 11.
Configuration port 0 register
Bit
7
6
5
4
3
2
1
0
Symbol
C0.7
C0.6
C0.5
C0.4
C0.3
C0.2
C0.1
C0.0
Default
11
Table 12.
Configuration port 1 register
Bit
7
6
5
4
3
2
1
0
Symbol
C1.7
C1.6
C1.5
C1.4
C1.3
C1.2
C1.1
C1.0
Default
11
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9698BS,118 | IC I/O EXPANDER I2C 40B 56HVQFN |
| PCA9555D,112 | IC I/O EXPANDER I2C 16B 24SOIC |
| PCA9555DB,112 | IC I/O EXPANDER I2C 16B 24SSOP |
| PCA9555PW,112 | IC I/O EXPANDER I2C 16B 24TSSOP |
| 5-531478-4 | CONT.MINI-LEAF STRIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9539PW118 | 制造商:NXP Semiconductors 功能描述:IC I/O EXPANDER 16BIT 400KHZ TSSOP24 |
| PCA9539PWE4 | 功能描述:接口-I/O擴展器 16-Bit I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9539PWG4 | 功能描述:接口-I/O擴展器 Rem 16B I2C & SMBus Low-Pwr I/O Exp RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9539PWR | 功能描述:接口-I/O擴展器 16-Bit I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9539PWRE4 | 功能描述:接口-I/O擴展器 16-Bit I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。