- 您現在的位置：買賣IC網 > PDF目錄367813 > PCD6001 (NXP Semiconductors N.V.) Digital telephone answering machine chip PDF資料下載
參數資料
| 型號： | PCD6001 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Digital telephone answering machine chip |
| 中文描述： | 數字電話應答機芯片 |
| 文件頁數： | 64/96頁 |
| 文件大?。?/td> | 385K |
| 代理商： | PCD6001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
2001 Apr 17
64
Philips Semiconductors
Product specification
Digital telephone answering machine chip
PCD6001
14 ANALOG VOLTAGE REFERENCE (AVR)
14.1
Bandgap reference
The Analog Voltage Reference circuitry (AVR) includes a
bandgap circuit with a nominal output voltage of about
1.25 V. This voltage is used by the power-on reset block
and by the analog voltage source to generate the
reference voltage V
REF
.
Block AVRisalways on,even in System-offmode, and will
consume only a few
μ
A of current. The output of AVR is
directly connected to the power-on reset block and it
determines the power-on reset threshold levels accuracy
in first order. The connection from AVR to the analog
voltage source circuitry (AVS, see Section 14.2) is via an
internal series resistor of about 500 k
(typical). The
voltage after this resistor is connected to pin V
BGP
, which
allows an external capacitor (100 nF) to be connected to
filter out any noise from AVR otherwise entering AVS.
With this configuration the noise at pin V
BGP
will be about
115 dBmp. The pin also allows a direct measurement of
the bandgap voltage, but no current must be drawn.
In order to guarantee a correct start-up of the bandgap
voltage under all conditions, a supply voltage ramp test is
performed on each device. The bandgap voltage is
compared against specified values at the indicated times
(see Fig.30). The test setup intends to reflect the worst
case start-up conditions which may occur in an application
(for initial power-up and after short power drop). Note that
t
rise
is critical and should not be greater than indicated in a
given application. Other indicated times (t
settle
and t
rise
)
reflect the worst case conditions for the device and
therefore can change in the application.
handbook, full pagewidth
MGT445
tfall
tsettle
trise
t
measure VBGP
VDDA
0 V
0.6 V
2.5 V
tfall = 2 ms
tsettle = 45 ms
trise = 20 ms
Fig.30 Bandgap voltage test setup.
相關PDF資料 |
PDF描述 |
|---|---|
| PCD6001H | Digital telephone answering machine chip |
| PCD6001U | Digital telephone answering machine chip |
| PCD8582D-2P | 256 x 8-bit CMOS EEPROMS with I2C-bus interface |
| PCD8582D-2 | 256 x 8-bit CMOS EEPROMS with I2C-bus interface |
| PCD8582D-2T | 256 x 8-bit CMOS EEPROMS with I2C-bus interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD6001H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital telephone answering machine chip |
| PCD6001U | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital telephone answering machine chip |
| PCD6002H/2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| PCD6003 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital telephone answering machine chip |
| PCD6003H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital telephone answering machine chip |
發布緊急采購，3分鐘左右您將得到回復。