- 您現在的位置：買賣IC網 > PDF目錄369952 > PCM3500DATASHEET PCM3500 Data Sheet - Low Voltage. Low Power. 16-Bit. Mono SoundPlus VOICE PDF資料下載
參數資料
| 型號： | PCM3500DATASHEET |
| 英文描述： | PCM3500 Data Sheet - Low Voltage. Low Power. 16-Bit. Mono SoundPlus VOICE |
| 中文描述： | PCM3500數據表-低電壓。低功耗。 16位。單SoundPlus語音 |
| 文件頁數： | 21/26頁 |
| 文件大?。?/td> | 199K |
| 代理商： | PCM3500DATASHEET |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁
21
PCM3500
V
REF
1 (pin 2) and V
REF
2 (pin 3) are reference voltages used
by the delta-sigma modulators. They are brought out strictly
for decoupling purposes. V
REF
1 and V
REF
2 are not to be
used to bias external circuits. A 1
μ
F to 10
μ
F aluminum
electrolytic or tantalum capacitor is recommended for
decoupling on each pin. These capacitors should be located
as close as possible to pins 2 and 3.
Power Supplies and Grounding
V
CC
(pin 24) and V
DD
(pin 13) should be connected directly
to the +2.7V to +3.6V analog power supply, as shown in
Figure 16. The AGNDs (pins 5, 21, and 23) and DGND (pin
14) should be connected directly to the analog ground.
Power supply bypass capacitors should be located as close
to the power supply pins as possible in order to ensure a low
impedance connection. A combination of a 10
μ
F aluminum
electrolytic or tantalum capacitor in parallel with a 0.1
μ
F
ceramic capacitor is recommended for both V
CC
and V
DD
.
V
DD
and V
CC
should not be connected to separate digital and
analog power supplies. This can lead to an SCR latch-up
condition, which can cause either degraded device perfor-
mance or catastrophic failures.
PCB LAYOUT GUIDELINES
The recommended PCB layout technique is shown in Figure
18. The analog and digital section of the board are separated
by a split ground plane, with the PCM3500 positioned
entirely over the analog section of the board. The AGNDs
(pins 5, 20, and 23) and DGND (pin 14) are connected
directly to the analog ground plane. The power supply pins,
V
CC
(pin 13) and V
DD
(pin 24), are routed directly to the
+2.7V to +3.6V analog power supply using wide copper
traces (100 mils or wider recommended) or a power plane.
Power supply bypass and reference decoupling capacitors
are shown located as close as possible to the PCM3500.
The PCM3500 is oriented so that the digital pins are facing
the ground plane split. Digital connections should be made
as short and direct as possible to limit high frequency
radiation and coupling. Series resistors (from 20
to 100
)
may be put in series with the system clock, FS, BCK, and
FSO lines to reduce or eliminate overshoot on clock edges,
further reducing radiated emissions. The split ground plane
should be connected at one point by a trace, wire, or ferrite
bead. Often the board will be designed to have several
jumper points for the common ground connection, so that
the best performance can be derived through experimenta-
tion.
An alternative technique, using a single power supply or
battery, is shown in Figure 19. This technique is more
suitable for portable applications.
FIGURE 18. Recommended PCB Layout Technique.
FIGURE 19. PCB Layout Using a Single-Supply or Battery.
PCM3500
V
CC
V
DD
AGND
Analog
Ground
Digital
Ground
DGND
Digital Power
Supply
Analog Power
Supply
+3.3V
+3.3V
Common
Connection
DIGITAL SECTION
ANALOG SECTION
Host
and
Logic
Digital I/Os
Split Grounds
PCM3500
V
CC
V
DD
AGND
Split Grounds
Ferrite
Beads
Analog
Ground
Digital
Ground
DGND
DIGITAL SECTION
ANALOG SECTION
Host
and
Logic
Common
Supply
Digital I/Os
相關PDF資料 |
PDF描述 |
|---|---|
| PCM3793A | 16-Bit, Low-Power Stereo Audio CODEC With Microphone Bias, Headphone, and Digital Speaker Amplifier |
| PCM3793ARHBR | 16-Bit, Low-Power Stereo Audio CODEC With Microphone Bias, Headphone, and Digital Speaker Amplifier |
| PCM3793ARHBRG4 | 16-Bit, Low-Power Stereo Audio CODEC With Microphone Bias, Headphone, and Digital Speaker Amplifier |
| PCM3793ARHBT | 16-Bit, Low-Power Stereo Audio CODEC With Microphone Bias, Headphone, and Digital Speaker Amplifier |
| PCM3793ARHBTG4 | 16-Bit, Low-Power Stereo Audio CODEC With Microphone Bias, Headphone, and Digital Speaker Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCM3500E | 功能描述:接口—CODEC Lo-Vlt Lo-Pwr Mono Voice/Modem Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| PCM3500E/2K | 功能描述:接口—CODEC Lo-Vlt Lo-Pwr Mono Voice/Modem Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| PCM3500E/2KG4 | 功能描述:接口—CODEC Lo-Vlt Lo-Pwr Mono Voice/Modem Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| PCM3500EG4 | 功能描述:接口—CODEC Lo-Vlt Lo-Pwr Mono Voice/Modem Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| PCM3501 | 制造商:BB 制造商全稱:BB 功能描述:Low Voltage, Low Power, 16-Bit, Mono VOICE/MODEM CODEC |
發布緊急采購，3分鐘左右您將得到回復。