- 您現在的位置：買賣IC網 > PDF目錄367860 > PDIUSBD12PW (NXP SEMICONDUCTORS) nullUSB interface device with parallel bus PDF資料下載
參數資料
| 型號： | PDIUSBD12PW |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | nullUSB interface device with parallel bus |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PDSO28 |
| 封裝： | 4.40 MM , PLASTIC, MO-153, SOT-361-1, TSSOP-28 |
| 文件頁數： | 15/35頁 |
| 文件大?。?/td> | 838K |
| 代理商： | PDIUSBD12PW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Philips Semiconductors
PDIUSBD12
USB interface device with parallel bus
Product data
Rev. 08 — 20 December 2001
15 of 35
9397 750 09238
Koninklijke Philips Electronics N.V. 2001. All rights reserved.
11.3 Data flow commands
Data flow commands are used to manage the data transmission between the USB
endpoints and the external microcontroller. Much of the data flow is initiated via an
interrupt to the microcontroller. The microcontroller utilizes these commands to
access and determine whether the endpoint FIFOs have valid data.
11.3.1
Read interrupt register
Code (Hex) —
F4
Transaction —
read 2 bytes
Table 7:
Bit
7
Set DMA command: bit allocation
Symbol
ENDPOINT INDEX 5
INTERRUPT ENABLE
Description
A ‘1’ allows for an interrupt to be generated whenever
the endpoint buffer is validated (see
Section 11.3.8
“Validate buffer”
command). Normally turned off for
DMA operation to reduce unnecessary CPU servicing.
A ‘1’ allows for an interrupt to be generated whenever
the endpoint buffer contains a valid packet. Normally
turned off for DMA operation to reduce unnecessary
CPU servicing.
A ‘0’ signifies a normal interrupt pin mode where an
interrupt is generated as a logical OR of all the bits in
the interrupt registers. A ‘1’ signifies that the interrupt
will occur when Start of Frame clock (SOF) is seen on
the upstream USB bus. The other normal interrupts are
still active.
When this bit is set to ‘1’, the DMA operation will
automatically restart.
This bit determines the direction of data flow during a
DMA transfer. A ‘1’ means external shared memory to
PDIUSBD12 (DMA Write); a ‘0’ means PDIUSBD12 to
the external shared memory (DMA Read).
Writing a ‘1’ to this bit will start DMA operation through
the assertion of pin DMREQ. The main endpoint buffer
needs to be full (for DMA Read) or empty (for DMA
Write) before DMREQ will be asserted. In a single
cycle DMA mode, the DMREQ is deactivated upon
receiving DMACK_N. In burst mode DMA, the DMREQ
is deactivated after the number of burst is exhausted.
It is then asserted again for the next burst. This process
continues until EOT_N is asserted together with
DMACK_N and either RD_N or WR_N, which will reset
this bit to ‘0’ and terminate the DMA operation. The
DMA operation can also be terminated by writing a
‘0’ to this bit.
Selects the burst length for DMA operation:
00 Single-cycle DMA
01 Burst (4-cycle) DMA
10 Burst (8-cycle) DMA
11 Burst (16-cycle) DMA
6
ENDPOINT INDEX 4
INTERRUPT ENABLE
5
INTERRUPT PIN
MODE
4
AUTO RELOAD
3
DMA DIRECTION
2
DMA ENABLE
1 to 0
DMA BURST
相關PDF資料 |
PDF描述 |
|---|---|
| PDIUSBH11A | Universal Serial Bus hub(通用串行總線集線器) |
| PDIUSBH11ANB | Universal Serial Bus Hub |
| PDIUSBH11AD | Universal Serial Bus Hub |
| PDIUSBH11 | Universal Serial Bus Hub |
| PDIUSBH11D | Universal Serial Bus Hub |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDIUSBD12PW,112 | 功能描述:USB 接口集成電路 USB I-FACE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| PDIUSBD12PW,118 | 功能描述:USB 接口集成電路 USB INTRFC W/PARL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| PDIUSBD12PW112 | 制造商:ST-Ericsson 功能描述:INTERFACE USB W/PARALLEL BUS 28TSSOP |
| PDIUSBD12PWAA | 功能描述:IC USB INTRFC W/PARL BUS 28TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| PDIUSBD12PWDH | 功能描述:USB 接口集成電路 USB I-FACE W/PARALLEL BUS RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。