- 您現在的位置：買賣IC網 > PDF目錄367860 > PDIUSBD12PW (NXP SEMICONDUCTORS) nullUSB interface device with parallel bus PDF資料下載
參數資料
| 型號： | PDIUSBD12PW |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | nullUSB interface device with parallel bus |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PDSO28 |
| 封裝： | 4.40 MM , PLASTIC, MO-153, SOT-361-1, TSSOP-28 |
| 文件頁數： | 7/35頁 |
| 文件大?。?/td> | 838K |
| 代理商： | PDIUSBD12PW |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Philips Semiconductors
PDIUSBD12
USB interface device with parallel bus
Product data
Rev. 08 — 20 December 2001
7 of 35
9397 750 09238
Koninklijke Philips Electronics N.V. 2001. All rights reserved.
7.
DMA transfer
Direct Memory Address (DMA) allows an efficient transfer of a block of data between
the host and local shared memory. Using a DMA controller, data transfer between the
PDIUSBD12’s main endpoint (endpoint 2) and local shared memory can happen
autonomously without local CPU intervention.
Preceding any DMA transfer, the local CPU receives from the host the necessary
setup information and programs the DMA controller accordingly. Typically, the DMA
controller is set up for demand transfer mode and the byte count register and the
address counter are programmed with the right values. In this mode, transfers occur
only when the PDIUSBD12 requests them and are terminated when the byte count
register reaches zero. After the DMA controller has been programmed, the DMA
enable bit of the PDIUSBD12 is set by the local CPU to initiate the transfer.
The PDIUSBD12 can be programmed for single-cycle DMA or burst mode DMA. In
single-cycle DMA, the DMREQ pin is deactivated for every single acknowledgement
by the DMACK_N before being re-asserted. In burst mode DMA, the DMREQ pin is
kept active for the number of bursts programmed in the device before going inactive.
This process continues until the PDIUSBD12 receives a DMA termination notice
through pin EOT_N. This will generate an interrupt to notify the local CPU that DMA
operation is completed.
For DMA read operation, the DMREQ pin will only be activated whenever the buffer is
full, signalling that the host has successfully transferred a packet to the PDIUSBD12.
With the double buffering scheme, the host can start filling up the second buffer while
the first buffer is being read out. This parallel processing increases the effective
throughput. When the host does not fill up the buffer completely (less than 64 bytes or
128 bytes for single direction ISO configuration), the DMREQ pin will be deactivated
at the last byte of the buffer regardless of the current DMA burst count. It will be
re-asserted on the next packet with a refreshed DMA burst count.
Similarly, for DMA write operations, the DMREQ pin remains active whenever the
buffer is not full. When the buffer is filled up, the packet is sent over to the host on the
next IN token and DMREQ will be reactivated if the transfer was successful. Also, the
double buffering scheme here will improve throughput. For non-isochronous transfer
(bulk and interrupt), the buffer needs to be completely filled up by the DMA write
Fig 3.
Example of a parallel interface to an 80C51 microcontroller.
PDIUSBD12
80C51
INT_N
A0
DATA [7:0]
WR_N
RD_N
CLKOUT
CS_N
ALE
XTAL1
RD/P3.7
WR/P3.6
P [0.7:0.0]/AD [7:0]
ANY I/O PORT (e.g. P3.3)
INTO/P3.2
SV00870
相關PDF資料 |
PDF描述 |
|---|---|
| PDIUSBH11A | Universal Serial Bus hub(通用串行總線集線器) |
| PDIUSBH11ANB | Universal Serial Bus Hub |
| PDIUSBH11AD | Universal Serial Bus Hub |
| PDIUSBH11 | Universal Serial Bus Hub |
| PDIUSBH11D | Universal Serial Bus Hub |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDIUSBD12PW,112 | 功能描述:USB 接口集成電路 USB I-FACE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| PDIUSBD12PW,118 | 功能描述:USB 接口集成電路 USB INTRFC W/PARL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| PDIUSBD12PW112 | 制造商:ST-Ericsson 功能描述:INTERFACE USB W/PARALLEL BUS 28TSSOP |
| PDIUSBD12PWAA | 功能描述:IC USB INTRFC W/PARL BUS 28TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| PDIUSBD12PWDH | 功能描述:USB 接口集成電路 USB I-FACE W/PARALLEL BUS RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。