參數資料
型號： PIC18F87J90-I/PT
廠商： Microchip Technology
文件頁數： 32/59頁
文件大小： 0K
描述： IC PIC MCU FLASH 128KB 80-TQFP
產品培訓模塊： PIC18 J Series MCU Overview
8-bit PIC® Microcontroller Portfolio
標準包裝： 119
系列： PIC® 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 48MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，LCD，LVD，POR，PWM，WDT
輸入/輸出數： 67
程序存儲器容量： 128KB（64K x 16）
程序存儲器類型： 閃存
RAM 容量： 3.8K x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 3.6 V
數據轉換器： A/D 12x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 80-TQFP
包裝： 托盤
產品目錄頁面： 644 (CN2011-ZH PDF)
配用： AC162079-ND - HEADER MPLAB ICD2 18F85J90 64/80
AC164323-ND - MODULE SKT FOR 100TQFP
PIC18F87J90 FAMILY
DS39933D-page 38
2010 Microchip Technology Inc.
3.3.1
CLOCK SOURCE SELECTION
The
System
Clock
Select
bits,
SCS<1:0>
(OSCCON<1:0>), select the clock source. The avail-
able clock sources are the primary clock defined by the
FOSC<2:0> Configuration bits, the secondary clock
(Timer1 oscillator) and the internal oscillator. The clock
source changes after one or more of the bits is written
to, following a brief clock transition interval.
The OSTS (OSCCON<3>) and T1RUN (T1CON<6>)
bits indicate which clock source is currently providing
the device clock. The OSTS bit indicates that the
Oscillator Start-up Timer (OST) has timed out and the
primary clock is providing the device clock in Primary
Clock modes. The T1RUN bit indicates when the
Timer1 oscillator is providing the device clock in
Secondary Clock modes. In power-managed modes,
only one of these bits will be set at any time. If neither
of these bits is set, the INTRC is providing the clock, or
the internal oscillator has just started and is not yet
stable.
The IDLEN bit determines if the device goes into Sleep
mode or one of the Idle modes when the SLEEP
instruction is executed.
The use of the flag and control bits in the OSCCON
register is discussed in more detail in Section 4.0
3.3.1.1
System Clock Selection and Device
Resets
Since the SCS bits are cleared on all forms of Reset,
this means the primary oscillator defined by the
FOSC<2:0> Configuration bits is used as the primary
clock source on device Resets. This could either be the
internal oscillator block by itself or one of the other
primary clock source (HS, EC, HSPLL, ECPLL1/2 or
INTPLL1/2).
In those cases when the internal oscillator block, with-
out PLL, is the default clock on Reset, the Fast RC
oscillator (INTOSC) will be used as the device clock
source. It will initially start at 1 MHz; the postscaler
selection that corresponds to the Reset value of the
IRCF<2:0> bits (‘100’).
Regardless of which primary oscillator is selected,
INTRC will always be enabled on device power-up. It
serves as the clock source until the device has loaded
its configuration values from memory. It is at this point
that the FOSC Configuration bits are read and the
oscillator selection of the operational mode is made.
Note that either the primary clock source, or the internal
oscillator, will have two bit setting options for the possible
values of the SCS<1:0> bits at any given time.
3.3.2
OSCILLATOR TRANSITIONS
PIC18F87J90 family devices contain circuitry to
prevent clock “glitches” when switching between clock
sources. A short pause in the device clock occurs dur-
ing the clock switch. The length of this pause is the sum
of two cycles of the old clock source and three to four
cycles of the new clock source. This formula assumes
that the new clock source is stable.
Clock transitions are discussed in greater detail in
Note 1: The Timer1 oscillator must be enabled to
select the secondary clock source. The
Timer1 oscillator is enabled by setting the
T1OSCEN bit in the Timer1 Control regis-
ter (T1CON<3>). If the Timer1 oscillator is
not enabled, then any attempt to select a
secondary clock source when executing a
SLEEP
instruction will be ignored.
2: It is recommended that the Timer1
oscillator be operating and stable before
executing the SLEEP instruction or a very
long delay may occur while the Timer1
oscillator starts.
相關PDF資料
PDF描述
PIC18F87K22-I/PTRSL MCU PIC 128K FLASH XLP 80TQFP
PIC18F97J60-I/PF IC PIC MCU FLASH 65KX16 100TQFP
PIC18LF1320-I/ML IC MCU FLASH 4KX16 EEPROM 28QFN
PIC18LF2450T-I/SO IC PIC MCU FLASH 8KX16 28SOIC
PIC18LF4320-I/PT IC MCU FLASH 4KX16 EEPROM 44TQFP
相關代理商/技術參數
參數描述
PIC18F87J90T-I/PT 功能描述:8位微控制器 -MCU Segmnt LCD 128KBFlsh 4KBRAM 12MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F87J93-I/PT 功能描述:8位微控制器 -MCU 80pn,SEG LCD,4KB RAM 128KB Flsh,12bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F87J93T-I/PT 功能描述:8位微控制器 -MCU 80pn,SEG LCD,4KB RAM 128KB Flsh,12bit ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F87J94-I/PT 制造商:Microchip Technology Inc 功能描述:80 PINS, 128KB FLASH, 4KB RAM, 16MIPS, NANOWATT XLP, LCD, US - Trays 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 128KB FLASH 80TQFP 制造商:Microchip Technology Inc 功能描述:80 pins, 128KB Flash, 4KB RAM, 16MIPS, nanoWatt XLP, LCD, USB, 80 TQFP 12x12x1mm
PIC18F87J94T-I/PT 制造商:Microchip Technology Inc 功能描述:80 PINS, 128KB FLASH, 4KB RAM, 16MIPS, NANOWATT XLP, LCD, US - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 128KB FLASH 80TQFP 制造商:Microchip Technology Inc 功能描述:8-bit Microcontrollers - MCU 80 pins, 128KB Flash 4KB RAM, 16MIPS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*