- 您現在的位置：買賣IC網 > PDF目錄1965 > PIC18LF96J65-I/PT (Microchip Technology)IC PIC MCU FLASH 48KX16 100TQFP PDF資料下載
參數資料
| 型號： | PIC18LF96J65-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 22/131頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PIC MCU FLASH 48KX16 100TQFP |
| 標準包裝： | 90 |
| 系列： | PIC® 18F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 41.667MHz |
| 連通性： | EBI/EMI，以太網，I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 70 |
| 程序存儲器容量： | 96KB（48K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 3808 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 數據轉換器： | A/D 16x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-TQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
PIC18F97J60 FAMILY
DS39762F-page 118
2011 Microchip Technology Inc.
8.3
Wait States
While it may be assumed that external memory devices
will operate at the microcontroller clock rate, this is
often not the case. In fact, many devices require longer
times to write or retrieve data than the time allowed by
the execution of table read or table write operations.
To compensate for this, the external memory bus can
be configured to add a fixed delay to each table opera-
tion using the bus. Wait states are enabled by setting
the WAIT Configuration bit. When enabled, the amount
of delay is set by the WAIT<1:0> bits (MEMCON<5:4>).
The delay is based on multiples of microcontroller
instruction cycle time and is added following the
instruction cycle when the table operation is executed.
The range is from no delay to 3 TCY (default value).
8.4
Port Pin Weak Pull-ups
With the exception of the upper address lines,
A<19:16>, the pins associated with the external mem-
ory bus are equipped with weak pull-ups. The pull-ups
are controlled by bits located at LATA<7:6> and
PORTA<7>. They are named RDPU, REPU and RJPU
and control pull-ups on PORTD, PORTE and PORTJ,
respectively. Setting one of these bits enables the
corresponding pull-ups for that port. All pull-ups are
disabled by default on all device Resets.
In Extended Microcontroller mode, the port pull-ups
can be useful in preserving the memory state on the
external bus while the bus is temporarily disabled
(EBDIS = 1).
8.5
Program Memory Modes and the
External Memory Bus
The PIC18F97J60 family of devices is capable of
operating in one of two program memory modes, using
combinations of on-chip and external program memory.
The functions of the multiplexed port pins depend on
the program memory mode selected, as well as the
setting of the EBDIS bit.
In Microcontroller Mode, the bus is not active and the
pins have their port functions only. Writes to the
MEMCOM register are not permitted. The Reset value
of EBDIS (‘0’) is ignored and the EMB pins behave as
I/O ports.
In Extended Microcontroller Mode, the external
program memory bus shares I/O port functions on the
pins. When the device is fetching, or doing table
read/table write operations on the external program
memory space, the pins will have the external bus
function.
If the device is fetching and accessing internal program
memory locations only, the EBDIS control bit will change
the pins from external memory to I/O port functions.
When EBDIS = 0, the pins function as the external bus.
When EBDIS = 1, the pins function as I/O ports.
If the device fetches or accesses external memory
while EBDIS = 1, the pins will switch to the external
bus. If the EBDIS bit is set by a program executing from
external memory, the action of setting the bit will be
delayed until the program branches into the internal
memory. At that time, the pins will change from external
bus to I/O ports.
If the device is executing out of internal memory when
EBDIS = 0, the memory bus address/data and control
pins will not be active. They will go to a state where the
active address/data pins are tri-state; the CE, OE,
WRH, WRL, UB and LB signals are ‘1’, and ALE and
BA0 are ‘0’. Note that only those pins associated with
the current address width are forced to tri-state; the
other pins continue to function as I/O. In the case of
16-bit address width, for example, only AD<15:0>
(PORTD and PORTE) are affected; A<19:16>
(PORTH<3:0>) continue to function as I/O.
In all external memory modes, the bus takes priority
over any other peripherals that may share pins with it.
This includes the Parallel Slave Port and serial
communication modules, which would otherwise take
priority over the I/O port.
8.6
16-Bit Data Width Modes
In 16-Bit Data Width mode, the external memory
interface can be connected to external memories in
three different configurations:
16-Bit Byte Write
16-Bit Word Write
16-Bit Byte Select
The configuration to be used is determined by
the WM<1:0> bits in the MEMCON register
(MEMCON<1:0>). These three different configurations
allow the designer maximum flexibility in using both
8-bit and 16-bit devices with 16-bit data.
For all 16-Bit Data Width modes, the Address Latch
Enable (ALE) pin indicates that the address bits,
AD<15:0>, are available in the external memory inter-
face bus. Following the address latch, the Output
Enable signal (OE) will enable both bytes of program
memory at once to form a 16-bit instruction word. The
Chip Enable signal (CE) is active at any time that the
microcontroller accesses external memory, whether
reading or writing. It is inactive (asserted high)
whenever the device is in Sleep mode.
In Byte Select mode, JEDEC standard Flash memories
will require BA0 for the byte address line and one I/O
line to select between Byte and Word mode. The other
16-Bit Data Width modes do not need BA0. JEDEC
standard, static RAM memories will use the UB or LB
signals for byte selection.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC24F16KL401-I/P | IC MCU 16BIT 16KB FLASH 20-PDIP |
| PIC24FJ128GA010-I/PF | IC PIC MCU FLASH 128KB 100TQFP |
| PIC24FJ256GA110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ256GB110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ64GA004-E/ML | IC PIC MCU FLASH 64K 44-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC1-R68-JT | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTQ | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTW | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KT | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KTQ | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
發布緊急采購，3分鐘左右您將得到回復。