參數資料
型號： QL5064-33BPB484C
英文描述： BUS CONTROLLER
中文描述： 總線控制器
文件頁數： 29/37頁
文件大?。?/td> 806K
代理商： QL5064-33BPB484C
QL5064 QuickPCI Data Sheet Rev D
29
QL5064 QuickPCI Data Sheet
23.0 QL5064 External Device Pins
Table 18: QL5064 External Device Pins
Pin/Bus Name
Type
Function
AD[63:0]
T/S
PCI Address and Data: 32 bit multiplexed address/data bus.
CBEN[7:0]
T/S
PCI Bus Command and Byte Enables: Multiplexed bus which contains byte enables for
AD[31:0] or the Bus Command during the address phase of a PCI transaction.
PAR
T/S
PCI Parity: Even Parity across AD[31:0] and C/BEN[3:0] busses. Driven one clock after
address or data phases. Master drives PAR on address cycles and PCI writes. The
Target drives PAR on PCI reads.
PAR64
T/S
PCI Parity Upper DWORD: Even Parity across AD[63:32] and C/BEN[7:4] busses.
FRAMEN
S/T/S
PCI Cycle Frame: Driven active by current PCI Master during a PCI transaction. Driven
low to indicate the address cycle, driven high at the end of the transaction.
REQ64N
S/T/S
PCI Request 64-bit transfer: Driven by the PCI Master to request a 64-bit transfer.
Same signal timing as FRAMEN.
DEVSELN
S/T/S
PCI Device Select. Driven by a Target that has decoded a valid base address.
ACK64N
S/T/S
PCI Acknowledge 64-bit Transfer: Driven by a Target which has decoded a valid base
address for a 64-bit data transfer. Same timing as DEVSELN.
CLK
IN
PCI System Clock Input.
RSTN
IN
PCI System Reset Input
REQN
T/S
PCI Request. Indicates to the Arbiter that this PCI Agent (Initiator) wishes to use the
bus. A point to point signal between the PCI Device and the System Arbiter.
GNTN
IN
PCI Grant. Indicates to a PCI Agent (Initiator) that it has been granted access to the PCI
bus by the Arbiter. A point to point signal between the PCI device and the System
Arbiter.
PERRN
S/T/S
PCI Data Parity Error. Driven active by the initiator or target two clock cycles after a data
parity error is detected on the AD and C/BEN busses.
SERRN
O/D
PCI System Error: Driven active when an address cycle parity error, data parity error
during a special cycle, or other catastrophic error is detected.
IDSEL
IN
PCI Initialization Device Select. Use to select a specific PCI Agent during System
Initialization.
IRDYN
S/T/S
PCI Initiator Ready. Indicates the Initiator’s ability to complete a read or write
transaction. Data transfer occurs only on clock cycles where both IRDYN and TRDYN
are active.
TRDYN
S/T/S
PCI Target Ready. Indicates the Target’s ability to complete a read or write transaction.
Data transfer occurs only on clock cycles where both IRDYN and TRDYN are active.
STOPN
S/T/S
PCI Stop. Used by a PCI Target to end a burst transaction.
INTAN
O/D
Interrupt A. Asynchronous Active-Low Interrupt Request.
相關PDF資料
PDF描述
QL5064-33BPB484I BUS CONTROLLER
QL5064-66APB456C BUS CONTROLLER
QL5064-66APB456I BUS CONTROLLER
QL5064-66APB484C BUS CONTROLLER
QL5064-66APB484I BUS CONTROLLER
相關代理商/技術參數
參數描述
QL5064-66APS484C-5541 制造商:QuickLogic Corporation 功能描述:
QL5064-66APS484I-5541 制造商:QuickLogic Corporation 功能描述:
QL5064-66BPS484C-5725 制造商:QuickLogic Corporation 功能描述:
QL5064-75CPS484C-5616 制造商:QuickLogic Corporation 功能描述:
QL5064-75CPS484I-5612 制造商:QuickLogic Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*