- 您現在的位置：買賣IC網 > PDF目錄368518 > RM2207D (Raytheon Company) Voltage Controlled Oscillator PDF資料下載
參數資料
| 型號： | RM2207D |
| 廠商： | Raytheon Company |
| 英文描述： | Voltage Controlled Oscillator |
| 中文描述： | 壓控振蕩器 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 74K |
| 代理商： | RM2207D |
PRODUCT SPECIFICATION
RC2207
7
For single supply operation, the DC voltage at pin 10 and the
timing terminals (pins 4 through 7) are equal and approxi-
mately 0.6V above V
B
, the bias voltage at pin 11 . The logic
levels at the binary keying terminals are referenced to the
voltage at pin 10.
On-Off Keying
The RC2207 can be keyed on and off by simply activating an
open circuited timing pin. Under certain conditions, the cir-
cuit may exhibit very low frequency (<1 Hz) residual oscilla-
tion in the off state due to internal bias current. If this effect
is undesirable, it can be eliminated by connecting a 10 M
resistor from pin 3 to + V
S
.
Frequency Control
(Sweep and FM)
The frequency of operation is controlled by varying the total
timing current, I
T
, drawn from the activated timing pin 4, 5,
6 or 7. The timing current can be modulated by applying a
control voltage, V
C
, to the activated timing pin through a
series resistor R
C
as shown in Figure 9.
For split supply operation, a negative control voltage, V
C
,
applied to the circuit of Figure 9 causes the total timing
current, I
T
, and the frequency, to increase.
As an example, in the circuit of Figure 9, the binary keying
inputs are grounded. Therefore, only timing pin 6 is
activated.
The frequency of operation determined by:
Pulse and Sawtooth Operation
The duty cycle of the output waveforms can be controlled by
frequency shift keying at the end of every half cycle of
oscillator output. This is accomplished by connecting one or
both of the binary keying inputs (pin 8 or 9) to the square-
wave output at pin 13. The output waveforms can then be
converted to positive or negative pulses and sawtooth
waveform.
Figure 10 is the recommended circuit connection for duty
cycle control. Pin 8 is shorted to pin 13 so that the circuit
switches between the 0 0 and the 1 0 logic states given in
Table 1. Timing pin 5 is activated when the output is high,
and pin 6 is activated when the squarewave output goes to a
low state.
The duty cycle of the output waveforms given as:
and can be varied from 0.1% to 99.9% by proper choice of
timing resistors. The frequency of oscillation, f, is given as:
The frequency can be modulated or swept without changing
the duty cycle by connecting R2 and R3 to a common control
voltage V
C
instead of to -V
S
. The sawtooth and the pulse
output waveforms are shown in the Typical Performance
Characteristics Graphs.
f
B
R3C
V
R3
R
C
V
C
–
)
---------------------------
–
Hz
=
Duty Cycle
R3
R2
=
f
2
C
---
+
R3
R2
=
Figure 8. Test Circuit for Single Supply Operation
65-2207-10
+V
S
12
5.1K
S1
6
R3
7
R4
4
R1
5
R2
R
L
9
8
1
2
3
13
14
Trianglewave
Output
Squarewave
Output
S2
C
+V
S
+V
S
0.1
μ
F
RC2207
Device
Under Test
Binary Keying
Inputs
10
11
0.1
μ
F
3.9K
I
S
相關PDF資料 |
PDF描述 |
|---|---|
| RM2A | SILICON RECTIFIER DIODES |
| RM2Z | SILICON RECTIFIER DIODES |
| RM2B | SILICON RECTIFIER DIODES |
| RM2C | SILICON RECTIFIER DIODES |
| RM4190D | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RM2207D/883B | 制造商:QP Semiconductor 功能描述:VOLTAGE CONTROLLED OSCILLATOR |
| RM2207D8 | 制造商:Fairchild Semiconductor Corporation 功能描述:QT# DVQR56 |
| RM220C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC |
| RM220D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC |
| RM220M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:R. F. Molded Chokes |
發布緊急采購，3分鐘左右您將得到回復。