參數資料
型號： S29AL032D70BAE002
廠商： Spansion Inc.
英文描述： 32 Megabit CMOS 3.0 Volt-only Flash Memory
中文描述： 32兆位的CMOS 3.0伏只閃存
文件頁數： 41/69頁
文件大?。?/td> 1970K
代理商： S29AL032D70BAE002
44
S29AL032D
S29AL032D_00_A3 June 13, 2005
Advan ce
In form ati o n
condition, the device halts the operation, and when the operation has exceeded the timing limits,
DQ5 produces a 1.
Under both these conditions, the system must issue the reset command to return the device to
reading array data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether
or not an erase operation has begun. (The sector erase timer does not apply to the chip erase
command.) If additional sectors are selected for erasure, the entire time-out also applies after
each additional sector erase command. When the time-out is complete, DQ3 switches from 0 to
1. The system may ignore DQ3 if the system can guarantee that the time between additional
sector erase commands will always be less than 50 μs. See also the Sector Erase Command
After the sector erase command sequence is written, the system should read the status on DQ7
(Data# Polling) or DQ6 (Toggle Bit I) to ensure the device has accepted the command sequence,
and then read DQ3. If DQ3 is 1, the internally controlled erase cycle has begun; all further com-
mands (other than Erase Suspend) are ignored until the erase operation is complete. If DQ3 is 0,
the device will accept additional sector erase commands. To ensure the command has been ac-
cepted, the system software should check the status of DQ3 prior to and following each
subsequent sector erase command. If DQ3 is high on the second status check, the last command
might not have been accepted. Table 18 shows the outputs for DQ3.
Table 18. Write Operation Status
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing
limits. See DQ5: Exceeded Timing Limits on page 43 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
Operation
DQ7
DQ6
DQ5
DQ3
DQ2
RY/BY#
Standard
Mode
Embedded Program Algorithm
DQ7#
Toggle
0
N/A
No toggle
0
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
0
Erase
Suspend
Mode
Reading within Erase
Suspended Sector
1
No toggle
0
N/A
Toggle
1
Reading within Non-Erase
Suspended Sector
Data
1
Erase-Suspend-Program
DQ7#
Toggle
0
N/A
0
相關PDF資料
PDF描述
S29AL032D90TFI042 32 Megabit CMOS 3.0 Volt-only Flash Memory
S29AL032D90TFI043 32 Megabit CMOS 3.0 Volt-only Flash Memory
S29CD016G0JDEI004 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76
S29CD016G0JDEI007 512K X 32 FLASH 2.7V PROM, 67 ns, UUC76
S29CD032J1JFAI122 1M X 32 FLASH 2.7V PROM, 54 ns, PBGA80
相關代理商/技術參數
參數描述
S29AL032D70BAI000 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 32Mbit 4M x 8bit 70ns 48-Pin FBGA Tray
S29AL032D70BAI030 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA Tray
S29AL032D70BAI032 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 4M/2M x 8bit/16bit 70ns 48-Pin FBGA T/R
S29AL032D70BFI000 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29AL032D70BFI030 功能描述:閃存 32MB 閃存 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*