- 您現在的位置：買賣IC網 > PDF目錄19364 > SAA7706H/N210S,518 (NXP Semiconductors)IC DSP CAR RADIO 80QFP PDF資料下載
參數資料
| 型號： | SAA7706H/N210S,518 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 42/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CAR RADIO 80QFP |
| 標準包裝： | 500 |
| 類型： | 汽車信號處理器 |
| 接口： | I²C，I²:S，LSB，SPDIF |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 3.30V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-BQFP |
| 供應商設備封裝： | 80-QFP（14x20） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
2001 Mar 05
47
Philips Semiconductors
Product specication
Car radio Digital Signal Processor (DSP)
SAA7706H
18 SOLDERING
18.1
Introduction to soldering surface mount
packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
18.2
Reow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 250
°C. The top-surface temperature of the
packages should preferable be kept below 220
°C for
thick/large packages, and below 235
°C for small/thin
packages.
18.3
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
18.4
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°C.
相關PDF資料 |
PDF描述 |
|---|---|
| PSA4531 | POWER SUPPLY OPEN FRAME 60W |
| TAP685M050CRW | CAP TANT 6.8UF 50V 20% RADIAL |
| EYM10DTKS | CONN EDGECARD 20POS DIP .156 SLD |
| MAX6692YMSA+T | IC SENSOR REMOTE SMBUS 8SOIC |
| SAA7706H/N107S,518 | IC DSP CAR RADIO 80QFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA7707H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Car radio Digital Signal Processor CDSP |
| SAA7708H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Car Radio Digital Signal Processor |
| SAA7709/N107 | 制造商:PHILIPS-SEMI 功能描述: |
| SAA7709H/N103 | 功能描述:音頻 DSP DIGITAL SIGNAL PROCESSOR RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| SAA7709H/N103,518 | 功能描述:音頻 DSP DIRAC-2 RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。