參數資料
型號： SC16C650BIN40,112
廠商： NXP Semiconductors
文件頁數： 17/48頁
文件大?。?/td> 0K
描述： IC UART SINGLE W/FIFO 40-DIP
標準包裝： 9
通道數： 1，UART
FIFO's： 32 字節
電源電壓： 2.5V，3.3V，5V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 通孔
封裝/外殼： 40-DIP（0.600"，15.24mm）
供應商設備封裝： 40-DIP
包裝： 管件
其它名稱： 568-2045-5
935274389112
SC16C650BIN40
SC16C650B_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 14 September 2009
24 of 48
NXP Semiconductors
SC16C650B
UART with 32-byte FIFOs and IrDA encoder/decoder
5
MCR[5]
INT type select.
logic 0 = enable interrupt output mode (normal default condition)
logic 1 = enable open source interrupt output mode. Provides shared
interrupts by producing a wire-OR output driver capability for interrupts. This
output appears at the INT pin. When using this option, an external pull-down
resistor of 200
to 500 must be tied from the INT pin to ground to provide
an acceptable logic 0 level
4
MCR[4]
Loopback. Enable the local loopback mode (diagnostics). In this mode the
transmitter output (TX) and the receiver input (RX), CTS, DSR, DCD, and RI are
disconnected from the SC16C650B I/O pins. Internally the modem data and
control pins are connected into a loopback data conguration (see Figure 7). In
this mode, the receiver and transmitter interrupts remain fully operational. The
Modem Control Interrupts are also operational, but the interrupts’ sources are
switched to the lower four bits of the Modem Control. Interrupts continue to be
controlled by the IER register.
logic 0 = disable loopback mode (normal default condition)
logic 1 = enable local loopback mode (diagnostics)
3
MCR[3]
OUT2. In the loopback mode this bit is used to control the modem DCD signal
via OUT2.
logic 0 = OUT2 is at logic 1. In the loopback mode, sets OUT2 (DCD)
internally to a logic 1.
logic 1 = OUT2 is at logic 0. In the loopback mode, sets OUT2 (DCD)
internally to a logic 0.
2
MCR[2]
OUT1, OUT. In the loopback mode, this bit is used to control modem RI interface
signal via OUT1 (OUT in the HVQFN32 package).
logic 0 = OUT1/OUT is at logic 1. In the loopback mode, sets RI internally to
logic 1.
logic 1 = OUT1/OUT is set at logic 0. In the loopback mode, sets RI internally
to logic 0.
1
MCR[1]
RTS
logic 0 = force RTS output to a logic 1 (normal default condition)
logic 1 = force RTS output to a logic 0
0
MCR[0]
DTR
logic 0 = force DTR output to a logic 1 (normal default condition)
logic 1 = force DTR output to a logic 0
Table 19.
Modem Control Register bits description …continued
Bit
Symbol
Description
相關PDF資料
PDF描述
V24C24H150BL CONVERTER MOD DC/DC 24V 150W
SC16C554IB64,157 IC UART QUAD W/FIFO 64-LQFP
V24C24H150B3 CONVERTER MOD DC/DC 24V 150W
ATMEGA644V-10MUR MCU AVR 64K FLASH 10MHZ 44QFN
SC28C94A1N,112 IC UART QUAD W/FIFO 48-DIP
相關代理商/技術參數
參數描述
SC16C652 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 32 bytes of transmit and receive FIFOs
SC16C652B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
SC16C652BIB48 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIB48,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIB48,151 功能描述:UART 接口集成電路 2CH. UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*