- 您現在的位置：買賣IC網 > PDF目錄372122 > SC16C754 (NXP Semiconductors N.V.) Quad UART with 64-byte FIFO PDF資料下載
參數資料
| 型號： | SC16C754 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Quad UART with 64-byte FIFO |
| 中文描述： | 四UART的64字節FIFO |
| 文件頁數： | 9/49頁 |
| 文件大?。?/td> | 622K |
| 代理商： | SC16C754 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Philips Semiconductors
SC16C754
Quad UART with 64-byte FIFO
Product data
Rev. 04 — 19 June 2003
9 of 49
9397 750 11618
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
With Auto-CTS, CTS must be active before the UART can transmit data.
Auto-RTS only activates the RTS output when there is enough room in the FIFO to
receive data and de-activates the RTS output when the RX FIFO is sufficiently full.
The halt and resume trigger levels in the TCR determine the levels at which RTS is
activated/deactivated.
If both Auto-CTS and Auto-RTS are enabled, when RTS is connected to CTS, data
transmission does not occur unless the receiver FIFO has empty space. Thus,
overrun errors are eliminated during hardware flow control. If not enabled, overrun
errors occur if the transmit data rate exceeds the receive FIFO servicing latency.
6.2.1
Auto-RTS
Auto-RTS data flow control originates in the receiver block (see
Figure 1 “Block
diagram.” on page 3
).
Figure 5
shows RTS functional timing. The receiver FIFO
trigger levels used in Auto-RTS are stored in the TCR. RTS is active if the RX FIFO
level is below the halt trigger level in TCR[3:0]. When the receiver FIFO halt trigger
level is reached, RTS is deasserted. The sending device (e.g., another UART) may
send an additional byte after the trigger level is reached (assuming the sending UART
has another byte to send) because it may not recognize the deassertion of RTS until
it has begun sending the additional byte. RTS is automatically reasserted once the
receiver FIFO reaches the resume trigger level programmed via TCR[7:4]. This
reassertion allows the sending device to resume transmission.
Fig 4.
Autoflow control (Auto-RTS and Auto-CTS) example.
RX
FIFO
SERIAL-TO-
PARALLEL
FLOW
CONTROL
TX
FIFO
PARALLEL-
TO-SERIAL
FLOW
CONTROL
PARALLEL-
TO-SERIAL
FLOW
CONTROL
SERIAL-TO-
PARALLEL
FLOW
CONTROL
TX
FIFO
RX
FIFO
UART 1
UART 2
D7-D0
RX
TX
RTS
CTS
TX
RX
CTS
RTS
D7-D0
002aaa228
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C754IA68 | Quad UART with 64-byte FIFO |
| SC16C754IB80 | Quad UART with 64-byte FIFO |
| SC2000 | Universal Timeslot Interchange |
| SC2001G-10 | Bus Exchanger |
| SC2001G-13 | Bus Exchanger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C754B | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs |
| SC16C754BIA68 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,518 | 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C754BIA68,529 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。