- 您現在的位置：買賣IC網 > PDF目錄11829 > SC16C850LIET,118 (NXP Semiconductors)IC UART SGL W/FIFO 36TFBGA PDF資料下載
參數資料
| 型號： | SC16C850LIET,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 16/55頁 |
| 文件大小： | 0K |
| 描述： | IC UART SGL W/FIFO 36TFBGA |
| 標準包裝： | 4,000 |
| 特點： | 可編程 |
| 通道數： | 1，UART |
| FIFO's： | 128 字節 |
| 規程： | RS485 |
| 電源電壓： | 2.5V |
| 帶并行端口： | * |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-TFBGA |
| 供應商設備封裝： | 36-TFBGA（3.5x3.5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
23 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
7.1 Transmit (THR) and Receive (RHR) Holding Registers
The serial transmitter section consists of an 8-bit Transmit Hold Register (THR) and
Transmit Shift Register (TSR). The status of the THR is provided in the Line Status
Register (LSR). Writing to the THR transfers the contents of the data bus (D7 to D0) to the
transmit FIFO. The THR empty flag in the LSR will be set to a logic 1 when the transmit
FIFO is empty or when data is transferred to the TSR.
The serial receive section also contains an 8-bit Receive Holding Register (RHR) and a
Receive Serial Shift Register (RSR). Receive data is removed from the SC16C850
receive FIFO by reading the RHR. The receive section provides a mechanism to prevent
false starts. On the falling edge of a start or false start bit, an internal receiver counter
starts counting clocks at the 16
× clock rate. After 71
2 clocks, the start bit time should be
shifted to the center of the start bit. At this time the start bit is sampled, and if it is still a
logic 0 it is validated. Evaluating the start bit in this manner prevents the receiver from
assembling a false character. Receiver status codes will be posted in the LSR.
7.2 Interrupt Enable Register (IER)
The Interrupt Enable Register (IER) masks the interrupts from receiver ready, transmitter
empty, line status and modem status registers. These interrupts would normally be seen
on the INT output pin.
Table 9.
Interrupt Enable Register bits description
Bit
Symbol
Description
7
IER[7]
CTS interrupt.
logic 0 = disable the CTS interrupt (normal default condition)
logic 1 = enable the CTS interrupt. The SC16C850 issues an interrupt when
the CTS pin transitions from a logic 0 to a logic 1.
6
IER[6]
RTS interrupt.
logic 0 = disable the RTS interrupt (normal default condition)
logic 1 = enable the RTS interrupt. The SC16C850 issues an interrupt when
the RTS pin transitions from a logic 0 to a logic 1.
5
IER[5]
Xoff interrupt.
logic 0 = disable the software flow control, receive Xoff interrupt (normal default
condition)
logic 1 = enable the receive Xoff interrupt
4
IER[4]
Sleep mode.
logic 0 = disable Sleep mode (normal default condition)
logic 1 = enable Sleep mode
3
IER[3]
Modem Status Interrupt. This interrupt will be issued whenever there is a modem
status change as reflected in MSR[3:0].
logic 0 = disable the modem status register interrupt (normal default condition)
logic 1 = enable the modem status register interrupt
2
IER[2]
Receive Line Status interrupt. This interrupt will be issued whenever a receive
data error condition exists as reflected in LSR[4:1].
logic 0 = disable the receiver line status interrupt (normal default condition)
logic 1 = enable the receiver line status interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B7H-IW-F4 | CONVERTER MOD DC/DC 52V 100W |
| VE-B7H-IW-F3 | CONVERTER MOD DC/DC 52V 100W |
| VI-BWZ-IW | CONVERTER MOD DC/DC 2V 40W |
| VE-B7H-IW-F1 | CONVERTER MOD DC/DC 52V 100W |
| AT32UC3L032-ZAUR | IC MCU AVR32 32K FLASH 48VQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C850LIET-G | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850LIET-S | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850SV | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V single UART, 20 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| SC16C850SVIBS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.8 V single UART, 20 Mbit/s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| SC16C850SVIBS,115 | 功能描述:UART 接口集成電路 UART 1-CH 128Byte FIFO 1.8V 32-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。